Planet MAP-3100 Software Manual Download Page 121

Page: 121 / 124

PLANET Mesh Network Manager Guide

4) Comment

•

An optional comment regarding the table entry

•

Data type: Display String

5) Active

•

Define the status of the table entry, either active or inactive

5.3.1.34 Status > DHCP Client

At the status tab, the DHCP Client list displays the DHCP Client information such as Mac

Address, IP Address and their hostname. This table is a read-only table, hence administrator

is unable to edit the table using the AP Configurator.

5.3.1.35 Command > Reboot

The reboot feature in the AP Configurator enables the NMS admin to restart the Mesh AP, thru

the SNMP protocol, even if they are located remotely from the user. Once executed, all the

service provided by the AP will be halted, until the reboot process completed successfully.

PLANET Mesh Network Manager Guide

Page121 of 124

Summary of Contents for MAP-3100





























































































































Search results

Summary of Contents for MAP-3100

Reviews:

Related manuals for MAP-3100

Brands by name

Popular brands

Planet MAP-3100, Software Manual

Search results

Summary of Contents for MAP-3100

Reviews:

Related manuals for MAP-3100

Brands by name

Popular brands