Planet MAP-3100 Software Manual Download Page 92

Page: 92 / 124

PLANET Mesh Network Manager Guide

5) Net

End

•

The last IP Address in the subnet for the assignment

•

Data type: IP Address

6) Max Lease Time

•

The maximum duration for the client to retain its current IP Address

•

Data type: Integer, in the range of 600 to 864000 seconds

7) Default Lease Time

•

The lease time defined for the client to retain its current IP Address. Once the

time is up, the IP Address will be released.

•

Data type: Integer, in the range of 600 to 864000 seconds

8) Domain

•

The domain name for the DHCP Server

•

Data type: DNS String

9) DNS

•

The IP Address of the DNS server of the subnet

•

Data type: IP Address

10) Router

•

The router IP Address of the subnet

•

Data type: IP Address

11) Comment

•

An optional comment for the particular table entry

•

Data type: Display String

12) Status

•

The status of that particular table entry, either active or inactive

PLANET Mesh Network Manager Guide

Page92 of 124

Summary of Contents for MAP-3100





























































































































Search results

Summary of Contents for MAP-3100

Reviews:

Related manuals for MAP-3100

Brands by name

Popular brands

Planet MAP-3100, Software Manual

Search results

Summary of Contents for MAP-3100

Reviews:

Related manuals for MAP-3100

Brands by name

Popular brands