Planet MAP-3100 Software Manual Download Page 85

Page: 85 / 124

PLANET Mesh Network Manager Guide

•

Select the type of the IPSec protocol.

•

Available selection:

x509

RSA

PSK

3) Local

•

The identifier of the local host.

•

Data type: Octet String

4) Remote

•

The identifier of the remote host at the other end

•

Data type: Octet String

5) Remote IP Address

•

The IP Address of the remote host.

•

Data type: IP Address

6) Remote Subnet, Remote Netmask

•

The Subnet where the remote host is located at, with its correspond netmask

•

Data type: IP Address

7) Local Certificate Password

•

The x.509 certificate pem passphrase, used when IPSec type x509 is

selected

•

Data type: Octet String

8) Local RSA Key

•

The RSA Key of the local host, used when IPSec type RSA is selected

•

Data type: Octet String

9) Remote

RSA

Key

•

The RSA Key of the remote host, used when IPSec type RSA is selected

•

Data type: Octet String

10) PSK

•

The PSK Key, used when IP Sec type PSK is selected

•

Data type: Octet String

PLANET Mesh Network Manager Guide

Page85 of 124

Summary of Contents for MAP-3100





























































































































Search results

Summary of Contents for MAP-3100

Reviews:

Related manuals for MAP-3100

Brands by name

Popular brands

Planet MAP-3100, Software Manual

Search results

Summary of Contents for MAP-3100

Reviews:

Related manuals for MAP-3100

Brands by name

Popular brands