Planet MAP-3100 Software Manual Download Page 72

Page: 72 / 124

PLANET Mesh Network Manager Guide

2) Netmask

•

The netmask for the Static IP Address.

•

Data type: IP Address

•

Network > WAN > PPPoE

Fill in the PPPoE’s username and password, then click the

Save Changes

button to activate

the PPPoE WAN interface type. Hit the

Back

button to back to the WAN Type configuration

page.

Parameters:

1) Enable

PPPoE

•

A checkbox to enable or disable the PPPoE service.

2) Username

•

The username of the PPPoE client

•

Data type: Display String

3) Password,

Confirm

•

The password corresponding to the username of the PPPoE client

•

Must key in the same input at the Confirm field to avoid mistakes

•

Data type: Display String

PLANET Mesh Network Manager Guide

Page72 of 124

Summary of Contents for MAP-3100





























































































































Search results

Summary of Contents for MAP-3100

Reviews:

Related manuals for MAP-3100

Brands by name

Popular brands

Planet MAP-3100, Software Manual

Search results

Summary of Contents for MAP-3100

Reviews:

Related manuals for MAP-3100

Brands by name

Popular brands