Planet MAP-3100 Software Manual Download Page 110

Page: 110 / 124

PLANET Mesh Network Manager Guide

•

The checking interval of the route watch dog, in seconds

•

Data Type: Integer, in the range of 10 to 60

•

Default value: 30

5.3.1.27 Services -> System Watch Dog

The Linux kernel watchdog is intended to monitor the integrity of the system periodically. In

case if there is any error occurs, the watch dog would trigger a system reboot in order to

prevent the system from failure.

Parameters

1) Enable Linux Watch Dog Service

•

A checkbox to enable or disable the route watchdog service of the Mesh AP

unit

2) Interval

•

The checking interval of the linux kernel watch dog, in seconds

•

Data Type: Integer, in the range of 10 to 60 seconds

•

Default value: 60

5.3.1.28 Services -> SSHD

At this page user will configure the SSH feature of the device.

Parameters

1) Enable SSHD Service

•

A checkbox to enable or disable the SSH service of the Mesh AP unit

PLANET Mesh Network Manager Guide

Page110 of 124

Summary of Contents for MAP-3100





























































































































Search results

Summary of Contents for MAP-3100

Reviews:

Related manuals for MAP-3100

Brands by name

Popular brands

Planet MAP-3100, Software Manual

Search results

Summary of Contents for MAP-3100

Reviews:

Related manuals for MAP-3100

Brands by name

Popular brands