Planet MAP-3100 Software Manual Download Page 70

Page: 70 / 124

PLANET Mesh Network Manager Guide

•

Default:

Disable.

5.3.1.4

Network > Network

The network panel defines the DNS settings. This DNS service translates the domain name

into IP Address form, which recognized by the Internet. If the primary server failed to perform

the translation, the secondary server will take over the process.

Parameters:

Primary DNS

•

Define the Primary DNS Server IP Address.

•

Data Type: IP Address

Secondary DNS

•

Define the secondary DNS Server IP Address

•

Data type: IP Address

Domain

•

An optional domain name for the DNS client

•

Data type: DNS String

Default Gateway

•

The default gateway IP Address for the static IP Address

•

Data type: IP Address

PLANET Mesh Network Manager Guide

Page70 of 124

Summary of Contents for MAP-3100





























































































































Search results

Summary of Contents for MAP-3100

Reviews:

Related manuals for MAP-3100

Brands by name

Popular brands

Planet MAP-3100, Software Manual

Search results

Summary of Contents for MAP-3100

Reviews:

Related manuals for MAP-3100

Brands by name

Popular brands