Planet MAP-3100 Software Manual Download

Page: 75 / 124

PLANET Mesh Network Manager Guide

5.3.1.6

Network > VLAN

The page is displaying the VLAN Table which is showing the activated VAP of the Mesh AP.

There are total of 16 VLANs available in the device. In order to activate an inactive VAP,

choose an entry from the Inactive VAP List, then click the

Edit Inactive VAP

button. Then the

Edit Inactive VAP – VLANx panel would appear. Similarly, to edit or disable an active VAP,

user can select the entry from the table, and hit the

Edit Active VAP

. Fill in the following

parameters:

1) ID

•

The ID for the VLAN interface.

•

The value is ranged between 1 to 4095, where 0 is reserved for VLAN0

2) Type

•

The type of the VLAN

•

The available options are static and dynamic

PLANET Mesh Network Manager Guide

Page75 of 124

Summary of Contents for MAP-3100





























































































































Search results

Summary of Contents for MAP-3100

Reviews:

Related manuals for MAP-3100

Brands by name

Popular brands

Planet MAP-3100, Software Manual

Search results

Summary of Contents for MAP-3100

Reviews:

Related manuals for MAP-3100

Brands by name

Popular brands