Planet MAP-3100 Software Manual Download Page 48

Page: 48 / 124

PLANET Mesh Network Manager Guide

Once the AP unit is rebooted completely, it will contain the information of the Alarm Host

System in the NMS. Hence, it will redirect the alarm message and notification to the NMS

when there is any.

4.2.3.26 View Log Files

There is a feature in the NMS allow the user to back-track the log files of the system. Select

View > View Log

Files from the NMS menu bar to invoke a new dialog box, as shown at the

following figures.

Then user can select the type of log to view, including Status Log and Alarm Log. Key in the

desired file name, or hit the button next to the column to select the file, and select the

Reload

button to load the content of the file.

PLANET Mesh Network Manager Guide

Page48 of 124

Summary of Contents for MAP-3100





























































































































Search results

Summary of Contents for MAP-3100

Reviews:

Related manuals for MAP-3100

Brands by name

Popular brands

Planet MAP-3100, Software Manual

Search results

Summary of Contents for MAP-3100

Reviews:

Related manuals for MAP-3100

Brands by name

Popular brands