Planet MAP-3100 Software Manual Download Page 59

Page: 59 / 124

PLANET Mesh Network Manager Guide

In order to invoke the live stat window, switch the NMS to the Map Container view, and then

look for the Live Stat Settings portion at the left bottom corner. User may enter the IP Address

of the target node (or just click on the node on the map to load the IP) to be monitored, and its

corresponding SNMP Key. Hit the

Start Live Stat

button to initiate the window.

At the popup live stat window, click the

Start Polling

button at the top to start the live stat.

The window consists of two parts: the System Stat and the Client Stat. The System Stat page

displays the memory status of the system and the statistic of the interfaces throughput. The

table will be updated at a certain interval, which is set by the Poll Interval field at the Live Stat

Settings corner.

PLANET Mesh Network Manager Guide

Page59 of 124

Summary of Contents for MAP-3100





























































































































Search results

Summary of Contents for MAP-3100

Reviews:

Related manuals for MAP-3100

Brands by name

Popular brands

Planet MAP-3100, Software Manual

Search results

Summary of Contents for MAP-3100

Reviews:

Related manuals for MAP-3100

Brands by name

Popular brands