Planet MAP-3100 Software Manual Download Page 67

Page: 67 / 124

PLANET Mesh Network Manager Guide

•

Read-only data

5.3.1.2

System > Syslog

The Syslog is a system feature to send the system log messages to a remote server.

Parameter

1) Enable

Syslog

•

A checkbox to enable or disable the syslog feature.

2) KLOG

•

A checkbox to enable or disable the Kernel Log service

3) Enable Remote Syslog

a. A checkbox to enable or disable the remote syslog server service

4) Remote Syslog Address

•

The address of the remote syslog server, who will receive all the syslog message

•

Data type: DNS String

5.3.1.3

System > Advanced Tuning

The Advance Tuning panel is divided to two parts, the connection tracking parameters and

the wireless distance. The Connection tracking portion determines the seconds of various

timeout parameters, where as the latter define the estimate operating distance in meters, for

the radio available in the device. Use the reset button to refill the value fields with the default

values.

PLANET Mesh Network Manager Guide

Page67 of 124

Summary of Contents for MAP-3100





























































































































Search results

Summary of Contents for MAP-3100

Reviews:

Related manuals for MAP-3100

Brands by name

Popular brands

Planet MAP-3100, Software Manual

Search results

Summary of Contents for MAP-3100

Reviews:

Related manuals for MAP-3100

Brands by name

Popular brands