Planet MAP-3100 Software Manual Download Page 44

Page: 44 / 124

PLANET Mesh Network Manager Guide

3. Click

the

SnmpWalk

button on the toolbar.

The output should now display at the Output area. It could take some time to

fetch all the data if the selected data is large.

Note: Please try to avoid Add or Delete the SNMP Table entry of the customized-MIB, since

there are some tables which are internally correlated, such as VLAN table and Wireless table.

Setting the table incorrectly would cause severe corruption in the system.

4.2.3.23 Load/Unload MIB

The MIB Reader of the NMS includes the feature to load and unload the MIB file from other

resource. Therefore, instead of the customized MIB, user can load other standard MIB into

the MIB Reader as well to read the parameter of the managed device.

In order to load a MIB, click on the

Load

button on the top of the MIB tree. A file chooser

window would popup, to prompt user to enter the desired MIB file. Click

Open

to load the file.

On the other hand, the

Unload

button next to the

Load

button would unload the existing MIB

in the tree. Select the unwanted MIB, click on the

Unload

button. A confirmation dialog box

would turn up, to get confirmation from the user to remove the selected MIB. Click the

Yes

button to proceed.

PLANET Mesh Network Manager Guide

Page44 of 124

Summary of Contents for MAP-3100





























































































































Search results

Summary of Contents for MAP-3100

Reviews:

Related manuals for MAP-3100

Brands by name

Popular brands

Planet MAP-3100, Software Manual

Search results

Summary of Contents for MAP-3100

Reviews:

Related manuals for MAP-3100

Brands by name

Popular brands