Planet GS-4210-16P2S User Manual Download

Page: 121 / 431

User’s Manual of GS-4210-16T2S_24T2S_16P2S_24P2S_48T4S

121

4.5 VLAN

4.5.1 VLAN Overview

A Virtual Local Area Network (VLAN)

is a network topology configured according to a logical scheme rather than the physical

layout. VLAN can be used to combine any collection of LAN segments into an autonomous user group that appears as a single

LAN. VLAN also logically segment the network into different broadcast domains so that packets are forwarded only between

ports within the VLAN. Typically, a VLAN corresponds to a particular subnet, although not necessarily.

VLAN can enhance performance by conserving bandwidth, and improve security by limiting traffic to specific domains.

A VLAN is a collection of end nodes grouped by logic instead of physical location. End nodes that frequently communicate with

each other are assigned to the same VLAN, regardless of where they are physically on the network. Logically, a VLAN can be

equated to a broadcast domain, because broadcast packets are forwarded to only members of the VLAN on which the

broadcast was initiated.

No matter what basis is used to uniquely identify end nodes and assign these nodes VLAN

membership, packets cannot cross VLAN without a network device performing a routing

function between the VLAN.

The Managed Switch supports IEEE 802.1Q VLAN. The port untagging function can be used

to remove the 802.1 tag from packet headers to maintain compatibility with devices that are

tag-unaware.

The Managed Switch's default is to assign all ports to a single 802.1Q VLAN named

DEFAULT_VLAN. As new VLAN is created, the member ports assigned to the new VLAN will

be removed from the DEFAULT_ VLAN port member list. The DEFAULT_VLAN has a VID = 1.

Summary of Contents for GS-4210-16P2S
















































































































































































































































































































































































































































Search results

Summary of Contents for GS-4210-16P2S

Reviews:

Related manuals for GS-4210-16P2S

Brands by name

Popular brands

Planet GS-4210-16P2S, User Manual

Search results

Summary of Contents for GS-4210-16P2S

Reviews:

Related manuals for GS-4210-16P2S

Brands by name

Popular brands