manualshive.com logo in svg

PINSSAR DPMRA01.A, Service Manual, Page: 95 / 96

Share
Download
PINSSAR DPMRA01.A Service Manual Download Page 95

PIN-M-02 DPMRA01.A Service Manual 

Copyright © Pinssar (Aust) Pty Ltd 2019. The PINSSAR logo is a registered trademark of Pinssar Pty Ltd 

 

Page 95 of 

96

 

14 

FAQ’s 

1. 

What is the correct way of turning “ON” the DPM Reader? 
Answer:

  Firstly,  ensure  the  external  mains  cable  is  fitted  to  a  wall  socket  and 

securely fastened into the AC Mains socket on the enclosure, that both the Mains 
and Battery Isolations Switches are in the “OFF” position and the power button is in 
the non-depressed state. 

Open Mains input’s cap by rotating it counter clockwise. 

Connect provided power cable to Mains input and wall socket. Turn on both isolation 
switches and press power button to turn on DPM Reader. Green light on the power 
button  should  be  on  within  15  seconds  of  pressing  the  button.  Before  the  first 
measurement, it may take up to half an hour to complete system initialisation.  
 

2.  What is the setting for the DPM Reader Measurement Cycle? 

Answer:

 The factory default setting is one completed measurement cycle every 320 

seconds.  The  measurement  time  interval  can  however  be  changed  via  the  HMI. 
Consult  with  your  local  Pinssar  representative  to  determine  any  impact  that  may 
occur by altering the sample interval 

 
3.  Does  the  DPM  Reader  require  regular  interval  or  periodic  servicing  even 

though it appears to be working fine? 
Answer:

  Yes.  Periodic  service  is  very  important  for  maintaining  measurement 

performance and to maximise the operational lifetime of DPM Reader. 
 

4.  Can any competent person complete the regular interval service? 

Answer:

  No.  Servicing,  inspections  and  diagnostic  trouble  shooting  must  be 

completed by a suitably qualified technician who has attended the required product 
familiarisation and training program. To safeguard this process, the DPM Reader is 
sealed with a tamper proof label and only registered and authorised personnel have 
replacement tamper proof labels if the seal must be broken for front door access.  
 
Should the DPM Reader be found not to have the tamper proof label in place, this 
may invalidate the warranty.  
 

5.  Whom should I contact when there is a question not seemingly addressed in 

the DPM Reader Installation or Service Manuals? 
Answer:

 You should contact your local Pinssar Representative, or contact Pinssar 

via email at 

[email protected]

  

 

6.  Where can replacement parts or modules be sourced? 

Answer

: Please contact PINSSAR in Australia directly. 

 

7.  Can similar or equivalent parts be used for service? 

Summary of Contents for DPMRA01.A

































































































Reviews:

No comments