PINSSAR DPMRA01.A Service Manual Download Page 68

Page: 68 / 96

PIN-M-02 DPMRA01.A Service Manual

Page 68 of

Installation

Warning: Set DPM Reader to Safety Control Level 4

1. Insert the Pressure Relief valve through the bottom of the enclosure checking

there is a rubber washer under the head of the pressure relief valve and a black
plastic washer under the inside of the enclosure.

2. Secure Lock nut on the inside of the enclosure.

3. Apply Thread Locking compound to the lock nut.

9.3.3

05-0816 Cyclone Assembly Replacement

Removal

Warning: Set DPM Reader to Safety Control Level 4

Refer to Figure 47.

1. Remove retainer from outside of enclosure using a Pinssar cyclone spanner

whilst holding the cyclone assembly from the inside with your hand.

2. Disconnect the black silicone hose from the cyclone fitting.

External View

Internal View

IGURE

EMOVAL OF

YCLONE

SSEMBLY

Remove retainer from outside of the enclosure.

Installation

Warning: Set DPM Reader to Safety Control Level 4

1. Insert the cyclone assembly into the enclosure from the inside of the DPM

Reader ensuring there is a gasket between the cyclone spacer ring and the
inside of the DPM Reader.

Summary of Contents for DPMRA01.A

































































































Search results

Summary of Contents for DPMRA01.A

Reviews:

PINSSAR DPMRA01.A, Service Manual, Page: 68 / 96

Search results

Summary of Contents for DPMRA01.A

Reviews: