PINSSAR DPMRA01.A Service Manual Download Page 46

Page: 46 / 96

PIN-M-02 DPMRA01.A Service Manual

Page 46 of

9.1.4

112204 Battery Replacement

Removal

Warning: Set DPM Reader to Safety Control Level 4

1. Unplug 2 connectors.

2. Using a No.2 Phillips screwdriver, remove the 2 screws from the battery clamp.

3. Carefully remove battery, ensuring battery terminals do not touch any metal

parts.

IGURE

ATTERY

EMOVAL

Installation

Warning: Set DPM Reader to Safety Control Level 4

1. Place clamp over the battery and fix with 2 screws using a No.2 Phillips head

screwdriver.

Reminder: Ensure the red wire is connected to the positive terminal and the
black wire to the negative terminal which are clearly marked on the battery.
Ensure a tight fitting of the cable terminals onto the corresponding fixed
battery terminals.

2. Allow the battery to charge for at least 4 hours in SCL 1C before turning the unit

on.

3. With the unit in SCL 4, open circuit test the battery. Voltage should be greater

than 12.8V.

9.1.5

Isolation Switch Fault Servicing

9.1.5.1

EST

WITCH

UNCTION

Warning: Set DPM Reader to Safety Control Level 1A

Step 1

Step 2

Summary of Contents for DPMRA01.A

































































































Search results

Summary of Contents for DPMRA01.A

Reviews:

PINSSAR DPMRA01.A, Service Manual, Page: 46 / 96

Search results

Summary of Contents for DPMRA01.A

Reviews: