manualshive.com logo in svg

Perkins New 1000 Series, Workshop Manual, Page: 255 / 290

Share
Download
Perkins New 1000 Series Workshop Manual Download Page 255

Workshop Manual, TPD 1350, issue 3

255

 

21

New 1000 Series

Data and dimensions

Note: This information is given as a guide for personnel engaged on engine overhauls. The dimensions which 
are shown are those which are mainly used in the factory. The information applies to all engines, unless an 
engine type code is shown.

Coolant pump, early gear driven pump

Type. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Centrifugal

Outside diameter of shaft  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  18,95/18,96 mm (0.7460/0.7465 in)

Diameter of bore of drive gear. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  18,90/18,92 mm (0.7441/0.7449 in)

Interference fit of drive gear on shaft. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  0,03/0,06 mm (0.0012/0.0024 in)

Diameter of bore of impeller  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  15,87/15,89 mm (0.6249/0.6257 in)

Outside diameter of shaft for impeller . . . . . . . . . . . . . . . . . . . . . . . . . . .  . 15,91/15,92 mm (0.6264/0.6268 in)

Interference fit of impeller on shaft  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  . 0,02/0,05 mm (0.0007/0.0020 in)

Diameter of bore for bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  38,06/38,08 mm (1.4983/1.4993 in)

Diameter of bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  38,09/38,10 mm (1.4995/1.5000 in)

Interference fit of bearing in pump body  . . . . . . . . . . . . . . . . . . . . . . . . . . .  . 0,01/0,04 mm (0.0004/0.0016 in)

Dimension of impeller boss to front face of pump body (fitted) . . . . . . . . . . . . . . . 7,7/8,0 mm (0.303./0.315 in)

Dimension of gear from rear flat face of pump body (fitted)  . . . . . . . . . . . . . . .  21,0/21,5 mm (0.827/0.846 in)

Dimension of gear from rear face of bearing (fitted) . . . . . . . . . . . . . . . . . . . .  . 0,47/1,53 mm (0.018/0.060 in)

Coolant pump, latest gear driven pump

Type. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Centrifugal

Coolant pump, belt driven

Type. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Centrifugal

Outside diameter of shaft for pulley. . . . . . . . . . . . . . . . . . . . . . . . . . .  . 24,587/24,600 mm (0.9679/0.9685 in)

Inside diameter of bore of pulley . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  24,628/24,648 mm (0.9696/0.9704 in)

Clearance fit of pulley on shaft  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  0,03/0,06 mm (0.001/0.002 in)

Diameter of bore of impeller  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  15,872/15,893 mm (0.6248/0.6257 in)

Outside diameter of shaft for impeller . . . . . . . . . . . . . . . . . . . . . . .  . 15,9055/15,9182 mm (0.6263/0.6267 in)

Interference fit of impeller on shaft  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  . 0,01/0,04 mm (0.0004/0.0016 in)

Impeller to body clearance  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  0,69/0,89 mm (0.027/0.035 in)

Impeller to body clearance, engine type AS  . . . . . . . . . . . . . . . . . . . . . . . . . . .  0,20/0,60 mm (0.008/0.024 in)

Diameter of bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  62,000 mm (2.440 in)

Diameter of bore for bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  62,019/62,000 mm (2.441/24.000 in)

Interference fit of bearing in pump body  . . . . . . . . . . . . . . . . . . . . . . . . . . .  . 0,01/0,04 mm (0.0004/0.0016 in)

Purchased from www.WorkshopManuals.co.uk

Summary of Contents for New 1000 Series



































































































































































































































































































Reviews:

No comments