PROHIBITED AREA FOR FLUE TERMINALS
57.
Aerion Range
REGULATORY COWL LOCATIONS
Figure 2.0 (Location of flue terminals of balanced flue, room-sealed, fan-assisted or outdoor appliances)
Legend:
I = Mechanical air inlet
M = Gas meter
P = Electricity meter or fuse box
S = Structure
T = Flue terminal
Z = Fan-assisted appliance only
Shading indicates prohibited area for flue ter-
minals
Ref.
Item
Minimum clearances
mm
Natural
draught
Fan
assisted
a
Below eaves, balconies and other projections:
For appliances up to 50MJ/h input
300
200
For appliances over 50MJ/h input
500
300
b
From the ground, above a balcony or other surface*
300
300
c
From a return wall or external cober*
500
300
d
From a gas meter (M) (see Note 5) (see Clause 5.11.5.9
for vent terminal location of regulator) (see Table 6.7 for
New Zealand requirements)
1000
1000
e
From an electricity meter or fuse box (P)• (see Note 5)
500
500
f
From a drain pipe or soil pipe
150
75
g
Horizontally from any building structure* or obstruction
facing a terminal
500
500
h
From any other flue terminal, cowl, or combustion air
intake*
500
300
j
Horizontally from an openable window, door, non-mechanical air inlet, or any other
opening inot a building with exception of sub-floor ventilation:
Appliances up to 150 MJ/h input*
500
300
Appliances over 150 MJ/h input up to 200 MJ/h input*
1500
300
Appliances over 200 MJ/h input up to 250 MJ/h input*
1500
500
Appliances over 250 MJ/h input*
1500
1500
All fan-assisted appliances, in the direction of discharge
-
1500
k
From a mechanical air inlet, including a spa blower
1500
1500
n
Vertically below an openable window, non-mechanical air inlet, or any other opening
inot a building with the exception of sub-floor ventilation:
For space heaters up to 50 MJ/h input
150
150
For other appliances up to 50 MJ/h input
500
500
For appliances over 50 MJ/h input and up to 150MJ/h
input
1000
1000
For appliances over 150 Mj/h input
1500
1500
Notes:
1) Where dimensions c, j, k cannot be acheived an
equivalent horizontal distance measured diagonally
from the nearest discharge point of the terminal to
the opening may be deemed by the Technical Regu-
lator to comply.
2) See Clause 6.9.4 for restrictions on a flue terminal
under a covered area.
3) See Figure J3 (from AS/NZS 5601) for minimum
clearances required from a flue terminal to an LPG
Gas cylinder. A flue terminal is considered to be a
source of ignition.
4) For minimum clearances not addressed above
acceptance should be obtained from the Technical
Regulator.
5) Minimum clearances d and e also apply to any
combustion air intake openings of appliances.
* Unless appliance is certified for closer installation
• Prohibited area below electricity meter or fuse box
extends to ground level
Summary of Contents for Aerion Series
