HAMPTON BAY H27-LP10 Owners & Installation Manual Download

Page: 1 / 48

MODELS: H27-NG10 Natural Gas H27-LP10 Propane

H27 Direct Vent Gas Fireplace

Owners &

Installation Manual

www.hampton-fire.com

FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4

919-484a

09.01.15

Tested by:

Installer

: Please complete the details on the back cover

and leave this manual with the homeowner.

Homeowner:

Please keep these instructions for future reference.

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other

appliance.

- WHAT TO DO IF YOU SMELL GAS

•

Do not try to light any appliance.

• Do not touch any electrical switch: do not use any phone in your building.

Leave the building immediately.

• Immediately call your gas supplier from a neighbour's phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call the fire department.

Installation and service must be performed by a qualified installer, service agency or the gas supplier.

WARNING

FIRE OR EXPLOSION HAZARD

ailure to follow safety warnings exactly could result in serious

injury, death, or property damage.

Summary of Contents for H27-LP10

















































Search results

Summary of Contents for H27-LP10

Reviews:

Related manuals for H27-LP10

Brands by name

Popular brands

HAMPTON BAY H27-LP10, Owners & Installation Manual

Search results

Summary of Contents for H27-LP10

Reviews:

Related manuals for H27-LP10

Brands by name

Popular brands