Paso PA8506-V Instructions For Use Manual Download Page 60

Page: 60 / 68

PA8506-V

VES Compact System

PA8500-VES | Voice Evacuation System

System Manual | 2014

8.9 MANUAL EMErGENCy - < EMErGENCy > MENU

Following.is.a.description.of.the.procedure.for.managing.emergencies.manually.by.an.authorised.operator.

8.9.1 General information

The. manual. emergency. mode. can. be. accessed. at. any. time.. It. has. priority. over. any. pre-recorded. messages. being. broadcast. at. the. time.

activated.by.an.external.peripheral.unit.connected.to.a.“Control.Input”.and.over.any.emergency.units.able.to.cover.the.six.output.zones.of.the.

unit.concerned..During.a.Manual.Emergency.(once.access.has.occurred),.the.display.will.show.the.operating.status.of.the.system.as.follows:

8.9.2 recommended procedure for managing emergencies manually

Thanks.to.its.double-channel.operation,.the.PA8506-V.system.enables.structured.management.of.the.alarm.messages,.of.silencing.of.the.

messages.and.of.selection.of.the.zones,.as.illustrated.in.detail.below..Following.is.a.list.of.activities.enabling.a.Manual.Emergency.to.be.

handled.rapidly.

Action required

How to proceed

result

Access.the.system

Press.the.

Emergency

.key.twice

The.zones.will.all.be.selected...

The.

Emergency

key.will.light.up.

Carry.out.an.overall.alarm.reset.

Press.the.RESET.key

The.alarms.will.be.reset,.all.the.zones.will.continue.to.

be.selected..The.alarm.LED.will.extinguish.

Reset.the.

beep

,.if.any,.

for.the.current.failure

Press.the.ESC.key

The.signalling.tone.of.the.monitoring.loudspeaker.will.

be.silenced.

Access the Manual Emergency

Send.the.message.to.all.zones.

Press.ALERT.or.EVAC.or.use.the.

Emergency.Microphone

The.message.is.played.out.to.all.the.zones..

The.alarm.LED.will.light.up.

despatch of alarm to all zones

Select.the.zones

Press.the.numerical.keys.

to.select.the.zones.

The.selected.zone.will.display.a.flashing.label..

Send.the.message

Press.ALERT.or.EVAC.or..

use.the.

Emergency

.Microphone

The.message.will.be.played.out.to.all.the.zones.

selected..The.alarm.LED.lights.up.

3) Send the alarm to one zone or group of zones

•.

Zone status bar:

Empty label

:.no.message.being.broadcast.to.this.zone.

EVAC

:.EVACUATION.message.being.broadcast.to.this.zone.

ALErT

:.ALERT:.ALERT.message.being.broadcast.to.this.zone.

MIC

:.life.announcement.being.broadcast.to.this.zone.with.the.hand-held.

microphone.

dIS

:.zone.disabled.for.alarms,.cannot.be.selected.(see.point.8.6.4).

FAIL

:.zone.with.the.speaker.line.in.a.failed.condition,.shown.even.if.the.type.of.failure.does.not.prejudice.the.output.signal.being.broadcast,.

or.operating.on.a.single.channel.due.to.failure.of.the.amplifier.so.that.the.envisaged.signal.cannot.be.broadcast.to.that.zone..For.details.see.

points.9.2.and.9.3.

•.

Led ALArM

LED.illuminated.to.indicate.that.the.VOICE.ALARM.condition.is.active.when.a.live.announcement.or.the.current.pre-recorded.message.are.being.

broadcast.to.at.least.one.zone.even.if,.in.a.12-zone.system,.the.zone.is.covered.by.the.other.PA8506-V.unit.connected.via.the.REMOTE.LINK.

•.

Labels associated with zones Z1-Z6

Zones with white background

:.zone.non.selected..The.current.message,.

if.any,.has.been.activated.automatically.

Zones with black background

:. zone. with. current. message. activated.

manually.

Flashing zones

:.zone.selected,.ready.for.a.message.to.be.sent.

manually.or.to.be.Reset.(see.Note..1).

•.

Title bar

EMErGENCy

:.access.achieved.for.a.manual.emergency.

EMErGENCy UNIT #

:.on-going.manual.emergency.activated.by.an.emergency.unit,.with.the.relevant.address,.connected.to.the.EMERGENCY.

UNIT.socket.

rEMOTE UNIT #

:.on-going.manual.emergency.activated.by.an.emergency.unit,.with.the.relevant.address,.connected.to.the.remote.PA8506-V.

unit,.in.a.12-zone.system.

Summary of Contents for PA8506-V





































































Search results

Summary of Contents for PA8506-V

Reviews:

Paso PA8506-V, Instructions For Use Manual, Page: 60 / 68

Search results

Summary of Contents for PA8506-V

Reviews: