Paso PA8506-V Instructions For Use Manual Download Page 50

Page: 50 / 68

PA8506-V

VES Compact System

PA8500-VES | Voice Evacuation System

System Manual | 2014

8.6.4

EMErGENCy UNIT CONFIG

Configuring an emergency unit

Panel.for.displaying.and.changing.the.operating.parameters.of.an.emergency.unit...
•.

Adjusting the sensitivity of the microphone

. -. Press.key.

Mic attenuation

.and.hold.it.down.

. -. Use.the.+/-.knob.to.set.the.required.level.of.attenuation.within.a.range.from.1.

(maximum.sensitivity).to.30.(minimum.sensitivity).

N.B.:.Once.the.parameter.has.been.set,.it.is.operational.both.in.the.Emergency.

mode.and.in.the.Broadcasting.mode.
•.

Setting the output volume

. -. Press.key.

.-.

Output level

and.hold.it.down.

. -. Use.the.

+/-

.knob.to.set.the.required.volume.level.within.a.range.from.

–6

.(minimum.output.level).to.

+21

.(maximum.output.level).

N.B.:. The. parameter. set. is. operational. only. in. the. Emergency. mode.. To. set. the. volume. for. the. Broadcasting. mode,. see. under. “AUDIO.

SETTING>.
•.

diagnostic settings:

. -. Press.key.

.–.

Test

.cyclically.

. . >..OFF:.diagnostics.disabled

. . >..ON:.diagnostics.enabled
N.B.:.The.addresses.of.the.stations.for.which.diagnostics.have.been.disabled.remain.in.any.case.in.the.configuration.of.the.acquired.system.
•.

Setting the 6-zone or 12-zone operating mode:

In.a.12-zone.system.with.two.PA8506-V.units.connected.to.one.another,.it.is.possible.to.configure.these.stations.for.operation.limited.to.the.6.

zones.covered.by.the.unit.in.question.or.extended.to.all.12.zones.within.the.system.as.a.whole..
-. Press.key

.–.

Mode

.cyclically.

. >.GLOBAL:.When.a.microphone.station.is.in.the.Global.mode,.it.can.be.used.to.make.selective.announcements.or.general.announcements.in.

all.12.zones.of.the.system..Access.is.governed.by.the.priority.settings.of.all.the.“Global”.or.“Local”.stations.connected.to.the.two.

PA8506-V.units.

. >.LOCAL:. When.a.microphone.station.is.in.the.Local.mode,.it.can.be.used.to.make.selective.announcements.or.general.announcements.

only.to.the.zones.covered.by.the.local.PA8506-V.unit.to.which.it.is.connected..This.mode.enables.another.“Local”.microphone.

station.connected.to.the.other.PA8506-V.unit.to.make.announcements.to.the.six.zones.it.covers.at.the.same.time..Access.is.

governed.by.the.priority.settings.of.all.the.stations.connected.to.the.PA8506-V.unit.with.which.they.are.associated.and.to.those.of.

the.other.PA8506-V.unit.that.are.set.in.the.“Global”.mode...

N.B.:.To.manage.the.system.correctly,.it.is.suggested.that.priority.levels.set.for.the.“Global”.microphone.bases.should.be.higher.than.those.set.for.the.

“Local”.microphone.bases..In.any.case,.the.PA8506-V.unit.with.its.own.hand-held.emergency.microphone.connected.to.the.front.panel.is.configured.for.

LOCAL.operation.and.with.the.highest.level.of.priority,.higher.than.any.remote.station.of.the.PMB132.range.

•.

Setting the level of the 20 kHz test tone:

This.control.adjusts.the.level.of.the.20.kHz.test.tone.generated.by.the.microphone.

station. so. as. to. offset. any. losses. of. the. signal. in. the. event. of. long-distance.

connections.

-. Press.key.6..The.line.“20.kHz.level”.will.appear,.followed.by.a.six-bar.vu-meter.

showing.the.value.set.for.the.test.signal..It.is.advisable.to.set.the.level.in.such.a.

way.that.at.least.two.or.three.bars.of.the.vu-meter.are.active.

-. Hold.down.key.6.and.use.the.+/-.knob.to.set.the.required.level,.within.a.range.

from.0.to.200.

N.B..The.change.in.the.level.shown.by.the.vu-meter.will.not.occur.immediately..After.

setting.the.level,.wait.for.about.30.seconds.before.reading.it.again.

•.

Priority

The.priority.level.set.for.the.microphone.station.is.shown.on.the.bottom.line.to.the.left..The.values.can.vary.between.8.(lowest.priority).and.14.

(maximum.priority)..The.parameter.is.displayed.only..To.change.its.value,.consult.the.manual.of.the.PMB132-V.and.PMB132/12-V.stations.(code.

no..11/716,.point.4.2).
•.

Low Cut Filter

The.setting.of.the.LOW.CUT.filter.is.shown.on.the.bottom.line.at.the.centre.

>.LCON:.filter.active

>.LCOFF:.filter.not.active

This.parameter.is.only.displayed..To.change.its.value,.consult.the.manual.of.the.PMB132-V.and.PMB132/12-V.stations.(code.no..11/716,.point.

4.6).
•.

P.T.T. Toggle

The.toggle.mode.of.the.PTT.key.is.shown.on.the.bottom.line.on.the.right-hand.side.

PTT:.Toggle.OFF.

LOCK:.Toggle.ON

Note:

.The.setting.of.this.parameter.is.operational.only.in.the.Broadcasting.mode..In.Emergency.conditions.the.Toggle.mode.is.always.OFF..This.parameter.

is.only.displayed..To.change.its.value,.consult.the.manual.of.the.PMB132-V.and.PMB132/12-V.stations.(code.no..11/716,.point.4.3).

Summary of Contents for PA8506-V





































































Search results

Summary of Contents for PA8506-V

Reviews:

Paso PA8506-V, Instructions For Use Manual, Page: 50 / 68

Search results

Summary of Contents for PA8506-V

Reviews: