manualshive.com logo in svg

Paso PA8506-V, Instructions For Use Manual, Page: 33 / 68

Share
Download
Paso PA8506-V Instructions For Use Manual Download Page 33

29

System Manual | 2014

PA8500-VES | Voice Evacuation System 

UK

PA8506-V 

|

 VES Compact System

8.4.2 

INPUT 2 

 

Management of the source on the IN 2 input

Hold. the. numerical. key. associated. with. the. function. down. and. turn. the. +/-.

knob.to.adjust.the.setting.

•.

Vol

:.

to.adjust.the.volume.within.the.range.of.-80dB/+40dB.(key.1.+.

knob).

•.

Chime

:.

to.view.the.setting.of.the.warning.signal.(ON/OFF)..See.point.

8.4.5.for.the.settings.

•.

Priority

:. priority.assigned.to.the.input.when.used.as.a.voice.source.for.

service.announcements..There.are.seven.priority.levels..This.

input.is.subject.to.muting.by.other.voice.sources.with.higher.

priority.levels.

•.

Ph

:.

Condition.set.for.the.phantom.power.supply.(OFF=not.active.

/.ON=active)..To.change.the.setting,.press.and.release.key.6.

(Ph).

•.

Zone list

:. List.of.zones.assigned.to.the.input.when.it.is.used.as.a.voice.source..To.select.one.of.the.36.available.lists,.hold.key.3.(ZONES).

down.and..turn.the.+/-.knob..If.the.list.that.is.selected.is.empty,.the.input.will.inhibit.use.of.the.voice.channel.by.PA.sources.having.

lower.priority.levels..For.details.about.programming.the.zone.list,.see.point.8.4.6.

•.

Mode

:.

Setting.the.operating.mode.of.the.input.for.using.a.

voice

.channel.as.a.PA.Source...

. .

Hold.key.5.(MODE).down.and.turn.the.+/-.knob.to.select.the.required.mode.from.among.the.following:

. .

>.

On

:.the.input.is.connected.directly.as.a.

voice

.source.and.is.operational.on.the.basis.of.its.priority.and.of.the.zone.list.selected..

. .

>.

Vox  level 1÷7

:.the.input.is.set.as.a.voice.source.with.automatic.precedence.activated.by.the.presence.of.the.incoming.audio.

signal..The.precedence.is.activated.when.the.audio.signal.exceeds.the.setting.for.the.threshold.level..Up.to.seven.increasing.

threshold.levels.can.be.chosen..Careful.adjustment.of.the.threshold.will.enable.prompt.broadcasting.of.the.signal.to.be.achieved,.

avoiding.involuntary.activation.of.precedence.by.noise.induced.on.the.cable.

. .

>.

Precedence

:. the. input. is. enabled. for. broadcasting. as. a. voice. source. by. closure. if. a. contact. connected. to. the. precedence.

terminals.

. .

.

Caution!.It.is.not.advisable.to.set.the.precedence.mode.on.this.input.if.the.IN.2.input.is.also.set.to.this.mode..If.required,.two.

microphones.with.precedence.contacts.can.be.connected.to.the.two.MIC.1.and.MIC.2.inputs,.using.the.“Mixing.on.INP..2”.mode.

for.the.IN..1.input.and.the.PRECEDENCE.mode.for.the.IN.2.input.

. .

>.

Off

:.input.disabled.for.the.PA.announcement.function;.the.source.connected.will.still.be.available.for.selection.as.a.BGM.Source.

•.

Hold on

:. Setting.of.the.release.time,.at.the.end.of.the.input.signal,.when.the.VOX.mode.is.selected..Hold.key.4.(HOLD).down.and.turn.the.

+/-.knob.to.choose.the.length.of.time.between.1.sec.and..100.secs...

The.RESET,.ALERT,.EVAC,.MENU.and.OK.keys.have.no.functions.

Press.ESC.to.return.to.the.AUDIO.SETTINGS.menu.

8.4.3 

INPUT 3 

 

Management of the source on input IN 3

Hold.the.numerical.key.associated.with.the.function.down.and.turn.the.+/-.

knob.to.adjust.the.setting.

•.

Vol

:.

to.adjust.the.volume.within.the.range.-80dB/+40dB.(key.1.+.

knob).

•.

Chime

:.

to.view.the.setting.of.the.warning.signal.(ON/OFF)..See.point.

8.4.5.for.the.settings.

•.

Priority

:. priority.assigned.to.the.input.when.it.is.used.as.a.voice.source.

for.service.announcements..There.are.seven.priority.levels..

This.input.is.subject.to.muting.by.other.voice.sources.with.

higher.priority.levels.

•.

Zone list

:. list.of.zones.assigned.to.the.input.when.it.is.used.as.a.voice.source..To.select.one.of.the.36.available.lists,.hold.key.3.(ZONES).

down.and.turn.the.+/-.knob..If.the.list.selected.is.empty,.the.input.will.inhibit.use.of.the.voice.channel.by.PA.sources.having.a.

lower.priority.

•.

Mode

:.

Setting.of.the.operating.mode.of.the.input.for.using.the.

voice

.channel.as.a.PA.Source...

. .

Hold.key.5.(MODE).down.and.turn.the.+/-.knob.to.select.the.required.mode.from.among.the.following:

. .

>.

On

:

. .

. The.input.will.be.connected.directly.as.a.voice.source.and.will.be.operational.on.the.basis.of.the.priority.and.of.the.zone.list.that.

is.selected..If.the.zone.list.is.empty,.the.input.will.inhibit.use.of.the.voice.channel.by.PA.sources.featuring.lower.priority.levels..

For.details.about.programming.the.zone.list,.see.point.8.4.6..

. .

>.

Vox level 1÷7

:

. .

. This.input.is.set.as.a.voice.source.with.automatic.precedence.activated.by.the.presence.of.the.incoming.audio.signal..The.

precedence.is.activated.when.the.audio.signal.exceeds.the.threshold.level.that.has.been.set..It.is.possible.to.choose.from.

among.seven.increasing.threshold.levels..Careful.adjustment.of.the.threshold.will.enable.prompt.broadcasting.of.the.signal.to.

be.achieved,.avoiding.involuntary.activation.of.precedence.by.noise.induced.on.the.cable.

. .

>.

Off

:.input.disabled.for.the.PA.announcement.function.

•.

Hold on

:. Setting.of.the.release.time,.at.the.end.of.the.input.signal,.when.the.VOX.mode.is.selected.Hold.key.4.(HOLD).down.and.turn..

the.+/-.knob.to.choose.the.length.of.time.between.1.sec.and..100.secs.

The.RESET,.ALERT,.EVAC,.MENU.and.OK.keys.are.not.operational.

Press.ESC.to.return.to.the.AUDIO.SETTINGS.menu.

Summary of Contents for PA8506-V





































































Reviews:

No comments