Paso PA8506-V Instructions For Use Manual Download Page 49

Page: 49 / 68

System Manual | 2014

PA8500-VES | Voice Evacuation System

PA8506-V

VES Compact System

8.6.3.4 COMMUNICATION TEST

Setting the test for internal data communication

Panel.for.enabling.and.disabling.testing.applied.to.communication.data.

between.internal.sections.of.PA8506-V.

•.. Press.the.appropriate.numerical.key.to.enable.or.disable.the

. diagnostic.test:

>.1-IC2.line:.

.(test.enabled).-.

off

(test.disabled)

>.2-Audio.SPI.line:.

.(test.enabled).-.

off

(test.disabled)

>.3-Relay.SPI.line:.

.(test.enabled).-.

off

(test.disabled)

8.6.3.5 EMErGENCy UNITS

Managing the addresses of the emergency units

Panel.for.displaying,.acquiring.and.selecting.the.addresses.of.the.emergency.

units.

First.of.all,.it.must.be.said.that.it.is.essential.for.each.station.to.have.its.

own.univocal.address..It.is.possible.to.connect.up.to.seven.PMB132-V.or.

PMB132/12-V. stations. to. a. PA8506-V. unit.. These. stations. . will. have. the.

addresses. numbered. from. 1. to. 7..The. default. address. of. all. microphone.

stations.is.1..At.the.time.of.connecting.each.of.them.to.the.EMERGENCY.

UNIT. port,. the. system. automatically. acquires. its. address. and. enables.

its. diagnosis.. In. order. to. avoid. lengthy. conflicts. between. stations,. it. is.

recommended.that.the.stations.should.be.added.one.at.a.time,.setting.each.

with.a.new.free.address..

N.B.: With regard to setting of the addresses, refer to the manual of the

microphone station, under the heading “SETTINGS>Address”.

Once.all.the.stations.have.been.connected.to.the.system,.the.EMERGENCY.UNIT.panel.displays.the.stations.that.have.been.acquired,.showing.

their.respective.addresses.under.the.line.of.the.corresponding.model.(PMB132-V.or.PMB132/12-V)..

•.

Up-dating of the system configuration

If.a.station.acquired.by.the.system.is.disconnected.or.is.given.a.different.address,.the.PA8506-V.signals.a.fault..

To.up-date.the.memory.on.the.basis.of.the.new.condition,.press.the.RESET.key..Any.addresses.of.stations.that.are.not.present.will.be.erased,.

keeping.only.those.that.are.detected.

•

Configuring the microphone station

Turn.the.+/-.knob.to.position.the.cursor.on.the.address.of.the.station.concerned.(when.an.address.is.free,.the.cursor.is.shown.on.the.two.lines.

of.both.models).

press OK

The.“EMERGENCY.UNIT.CONFIG”.panel.of.the.selected.station.will..appear.

Consult.point.8.6.4.“EMERGENCY.UNIT.CONFIG”.for.the.settings.of.the.single.bases.

To.return.to.the.previous.level,.press.ESC.

Summary of Contents for PA8506-V





































































Search results

Summary of Contents for PA8506-V

Reviews:

Paso PA8506-V, Instructions For Use Manual, Page: 49 / 68

Search results

Summary of Contents for PA8506-V

Reviews: