manualshive.com logo in svg

Paso PA8506-V, Instructions For Use Manual, Page: 47 / 68

Share
Download
Paso PA8506-V Instructions For Use Manual Download Page 47

43

System Manual | 2014

PA8500-VES | Voice Evacuation System 

UK

PA8506-V 

|

 VES Compact System

8.6.2 

CONTrOL OUTPUT

.

Local output contacts 

Panel.for.programming.the.six.local.output.contacts.(CONTROL.OUTPUTS).

and.the.two.service.relays,.RELAY.1.and.RELAY.2.

For.each.output.it.is.possible.to.choose.the.idle.status.and.to.associate.the.

system.status.event.leading.to.its.activation.

On.completing.the.programming,.press.ESC.to.return.to.the.OPERATOR.

menu.

8.6.2.1

.

Programming the output contacts   

Note:.The.display.will.show.the.programming.that.has.been.set.

Choosing the output to be programmed:

Hold.the.OUT.key.(

1

).down.and.turn.the.

+/-

.knob.to.select.the.number.of.the.output.from.among.the.following:

.

>.

OPEN COL. outputs from 1 to 6:

.open-collector.CONTROL.OUTPUTS.

.

>.

rELAy AUX outputs from 1 to 2:

.RELAY.1.and.RELAY.2.OUTPUTS.

Programming an output to associate it with a system event:

Hold.the.MODE.key.(

2

).down.and.turn.the.

+/-

.knob.to.select.one.of.the.following.options:.

.

.

.

>.

USEr MOdE: 

unprogrammed.output.

.

>.

Override Z1 - Z6:

.seizing.of.the.zone.indicated.by.a.PA.Source.or.a.VES.source.

.

>.

Voice Alarm State: 

system.currently.in.a.generic.“Voice.Alarm.Condition”.

.

>

 Manual Voice Alarm:

.system.currently.in.a.“Voice.Alarm.Condition”.activated.by.a.Manual.Emergency.(Operator).procedure.

.

>.

Automatic Voice Alarm:

.system.currently.in.a.“Voice.Alarm.Condition”.activated.by.an.Automatic.Emergency.(Control.Input).procedure..

>.

Z1- Z6

.

Voice Alarm:

.system.currently.in.a.“Voice.Alarm.Condition”.affecting.the.output.zone.indicated.

.

>.

Evac Message Playing:

.system.currently.in.a.“Voice.Alarm.Condition”.with.the.pre-recorded.Evac.message.being.played.out.

.

>.

Alert Message Playing:

.system.currently.in.a.“Voice.Alarm.Condition”.with.the.pre-recorded.Alert.message.being.played.out.

.

>.

disablement Condition: 

currently.in.a.“Disablement.Condition”.

.

>.

General Fault:

.currently.in.a.generic.“Fault.Warning.Condition”.

.

>.

Fault - Loudspk. Line: 

at.least.one.speaker.line.currently.in.a.“Fault.Warning.Condition”.

.

>

 Fault - Voice Alarm: 

at.least.one.VES.source.currently.in.a.“Fault.Warning.Condition”.

.

>.

Fault - Amplifier:

.at.least.one.amplifier.currently.in.a.“Fault.Warning.Condition”.

.

>.

Fault - Main Powerr:

.main.230.VAC.power.supply.currently.in.a.“Fault.Warning.Condition”.

.

>.

Fault - 24 VdC:

.secondary.24.VDC.currently.in.a.“Fault.Warning.Condition”.

.

>.

Fault - Control Input:

.at.least.one.local.input.contact.currently.in.a.“Fault.Warning.Condition”.

.

>.

Fault - Emerg. Unit:

.at.least.one.emergency.microphone.station.currently.in.a.“Fault.Warning.Condition”.

.

>.

Fault Line Z1 - Z6:

.one.of.the.speaker.lines.pertaining.to.the.zone.indicated.currently.in.a.“Fault.Warning.Condition”.

.

>.

reply Input 1-8:

.the.input.contact.indicated.is.in.an.active.condition...

.

.

......This.also.applies.to.inputs.that.are.not.programmed.or.that.are.inhibited.by.a.higher.priority.

.

>

 reply any Input:

.any.input.contact.is.in.an.active.condition...

.

.

.......This.also.applies.to.inputs.that.are.not.operational.or.that.are.inhibited.by.a.higher.priority.

Choice of the idle condition of an output with regard to the activating event (excluding the USEr MOdE):

Press.the.STATE.key.(6).to.select:

.

>.

Normal State OFF:

.output.de-activated.if.the.event.is.not.active.

.

>.

Normal State ON:

.output.active.if.the.event.is.not.active.

•..

Programming of the output contact to signal a System fault (System CPU Fault): 

The.RELAY.2.output.can.also.be.programmed.to.signal.a.“System.fault”.detected.by.the.watchdog.system...

After.selecting.the.RELAY.2.output:2:

•.Press.W-D.key.(5).to.select:

>

 watch dog OFF

for.an.output.not.programmed.to.signal.System.faults,

or

>.

watch dog ON

for.an.output.programmed.to.signal.System.faults.

Note:

.If.the.output.is.programmed.as.“watchdog.ON”,.the.idle.condition.of.the.output.can.only.be.“Normal.State.OFF”.

Summary of Contents for PA8506-V





































































Reviews:

No comments