manualshive.com logo in svg

Paso PA8506-V, Instructions For Use Manual, Page: 15 / 68

Share
Download
Paso PA8506-V Instructions For Use Manual Download Page 15

11

System Manual | 2014

PA8500-VES | Voice Evacuation System 

UK

PA8506-V 

|

 VES Compact System

5.4.3  Example n°3: Various types of PA source with progressive degrees of priority, “voice” amplification channel

Connection.by.way.of.example.of.one.table-top.microphone.station,.not..pre-amplified,.with.a.precedence.contact;.of.one.grip-type.microphone.

with.automatic.VOX.activation.over.music;.of.one.PABX.with.an.audio.output.for.automatic.announcements.over.the.sound-broadcasting.system.

and.digital.stations.of.the.PMB.range.for.service.announcements.with.zone.selection..For.details.concerning.the.settings.refer.to.the.relevant.

sections.indicated.under.AUDIO.SETTING.

A

.-.Table-top.base.with.electret.microphone,.balanced.output.connected.to.the.

IN.1.input.–.MIC.and.precedence.contact.connected.to.the.PPREC..input.

The.announcement.will.be.addressed.to.the.group.of.zones.indicated.in.the.

ZONE.LIST.on.the.basis.of.the.priority.set.

Set.the.via.the.INPUT.1.panel:. >MODE:.PRECEDENCE

.

.

>PH:.ON

.

.

>Priority:.3.

.

.

>Zone.list:.as.desired

.

.

>VOL.:.as.desired

Set.the.via.the.CHIME.panel:.

>.MIC.1:.ON.

N.B.:.In.a.12-zone.system,.the.microphone.input.that.uses.the.precedence.

function.on.one.PA8506-V.unit.is.not.shared.with.the.other.PA8506-V.unit.

and.is.broadcast.as.a.“local”.source...

B

.-.Grip-type.dynamic.microphone,.balanced.output.connected.to.the.input.

IN.2–.MIC.with.VOX.function.

The.announcement.will.be.addressed.to.the.group.of.zones.indicated.on.the.

ZONE.LIST.according.to.the.priority.that.is.set.

Set.the.via.the.INPUT.2.panel:. >MODE:.VOX

.

.

>PH:.OFF

.

.

>Priority:.1.

.

.

>Zone.list:.as.desired

.

.

>VOL.:.as.desired

Set.the.via.the.CHIME.panel:.

>.MIC.2:.OFF.

N.B.:.In.a.12-zone.system,.the.microphone.input.that.uses.the.VOX.function.

on.one.PA8506-V.unit.is.not.shared.with.the.other.PA8506-V.unit.and.is.

broadcast.as.a.“local”.source..

Caution! do not connect any other equipment to the LINE terminals of 

the IN.2 input.

C 

-.PABX.with.balanced.line.output.for.external.paging,.connected.to.the.IN.3.

input.–.LINE.with.VOX.function.

The.announcement.will.be.addressed.to.the.group.of.zones.indicated.on.the.

ZONE.LIST.depending.on.the.priority.that.is.set.

Set.the.via.the.INPUT.3.panel:. >MODE:.VOX

.

.

>PH:.OFF

.

.

>Priority:.7.

.

.

>Zone.list:.as.desired

.

.

>VOL.:.as.desired

Set.the.via.the.CHIME.panel:.

>.VOX:.OFF

N.B.:.In.a.12-zone.system,.the.line.input.that.uses.the.VOX.function.on.one.

PA8506-V.unit.is.not.shared.with.the.other.PA8506-V.unit.and.is.broadcast.as.

a.“local”.source”..If.necessary.make.a.parallel.connection.on.input.IN.3.of.the.other.PA8506-V.unit.and.also.set.the.input.used.on.the.remote.PA8506-V.

accordingly..

d

.-.Digital.microphone.stations.connected.in.cascade.formation.to.the.PAGING.UNIT.input..The.announcement.will.be.addressed.to.the.zones.indicated.

when.programming.the.keys.of.the.bases.depending.on.the.priority.set.for.each.base.

Set.the.PAGING.UNITS.panel:. >VOL.:.as.desired.(volume.of.the.whole.line.for.all.the.bases)

Set.the.CHIME.panel:.

>.UNIT:.ON

N.B.:.In.a.12-zone.system,.refer.to.point.5.5.for.the.operating.modes.of.the.PAGING.UNITS.

Sizing

:.For.each.PA8506-V.unit,.up.to.a.maximum.of.16.stations.of.the.PAGING.UNIT.range.can.be.connected..Use.the.Cat..5.SF/UTP.connecting.

cable,.with.its.shielding.plait..The.following.limits.must.be.observed.for.the.connections:

N..1.station.connected.to.a.line.800.metres.long.

N..8.stations.distributed.along.2.lines,.each.200.metres.long.(4.stations.per.line).

For.systems.calling.for.greater.distances.or.a.higher.number.of.stations.to.be.connected,.it.is.advisable.to.power.the.stations.by.means.of.the.additional.

power.supply.unit.connected.to.the.local.socket.of.the.base.

The.maximum.length.of.the.connecting.line,.adding.up.the.lines.connected.to.the.two.RJ45.sockets,.is.1.km..For.further.details.concerning.the.type.

of.power.supply,.the.configuration.of.the.cable,.programming.of.the.selection.keys.and.setting.of.the.priorities.and.addresses,.refer.to.the.Instruction.

Manual.of.the.stations.of.the.PMB.range.

The.following.PAGING.UNITS.can.be.connected.to.the.

PA8506-V

:

•.

PMB106-G

:.

6

-zone.paging.unit.

•.

PMB112-G

:.

12

-zone.paging.unit.

N.B.:  The  connections  between  the  PA8506-V  and 

PAGING UNITS must be made solely with Cat. 5 SF/UTP 

cables.

Nota: i collegamenti tra PA8506-V e PAGING UNITS sono da effettuarsi 

esclusivamente con cavi di tipo CAT. 5 SF/UTP.

C

A

B

d

d

Summary of Contents for PA8506-V





































































Reviews:

No comments