manualshive.com logo in svg

Paso PA8506-V, Instructions For Use Manual, Page: 43 / 68

Share
Download
Paso PA8506-V Instructions For Use Manual Download Page 43

39

System Manual | 2014

PA8500-VES | Voice Evacuation System 

UK

PA8506-V 

|

 VES Compact System

8.5.1.7  CONTrOL INPUT FAULT

 

diagnostics of the local control inputs  

From.the.FAULTS.panel.(point.8.5.1),.press.numerical.key.5.to.access.the.

panel. for. viewing. the. diagnostics. of. the. local. control. inputs. (CONTROL.

INPUTS).

The.diagnostic.state.of.each.item.monitored.is.reported,.as.shown.in.the.

following.table.

Press.ESC.to.return.to.the.panel.FAULTS.

Tab. 8.5.1.7

Label

Part being diagnosed

display

Cause

Action required

No.input..

fault.found

Input.contacts.

1.to.8

Empty.

list

No.failure,.or.monitoring.not.

enabled.for.any.input.contacts

-

Input.in.fault:

List.

number.of.

inputs

Break.or.short.circuit.in.the.line.

connecting.the.contact.

Check.integrity.of.the.line.connecting.the.

balancing.resistors.and.the.activation.contact..

If.the.problem.persists,.disconnect.the.line.

connecting.the.activation.contact.and.connect.

a.20.k

W

.resistor.between.the.+24V.service.

terminals.and.the.control.input..If.the.problem.

persists,.contact.Servicing.

Inputs.fault.

resumed:

Failure.cleared.due.to.previous.

failure.signal

Access.the.Report>.FAULTS.panel.from.the.

OPERATOR.menu.and.carry.out.a.MANUAL.

RESET.of.the.FAILURE.signal.

General.Input.

Fault:

Empty.

list

Failure.of.the.internal.communi-

cation.between.the.CPU.and.the.

inputs.controlled.stage.

If.the.problem.persists,.contact.Servicing.

General.Fault.

resumed:

Failure.cleared.due.to.previous.

failure.signal

Access.the.Report>.FAULTS.panel.from.the.

OPERATOR.menu.and.carry.out.a.MANUAL.

RESET.of.the.FAILURE.signal.

8.5.1.8  COMMUNICATION FAULT

.

diagnostics of the internal data communication

From.the.FAULTS.panel.(point.8.5.1),.press.numerical.key.6.and.access.the.

panel.for.viewing.the.diagnostics.of.the.internal.data.communication.

The. diagnostic. state. of. each. item. monitored. is. reported. in. the. following.

table.

Press.ESC.to.return.to.the.panel.FAULTS.

Label

data being diagnosed

display

Cause

Action required

I2C.line

Management.data.of.

amplifiers.and.keys.

interface.

All

OK

No.failure.

-

Audio.SPI.line

Management.data.of.

audio.matrix..

N.T.

NO.TEST..Diagnostics.disabled.

during.configuration.(see.

set>.

BACKGROUND.TEST).

-

Relay.SPI.line

Management.data.of.

outputs.switching.section.

Res.

Failure.(Fault.signal).cleared.

Access.the.Report>.FAULTS.panel.from.the.

OPERATOR.menu.and.carry.out.a.MANUAL.

RESET.of.the.FAILURE.signal.

Fault

Current.failure.due.to.

communication.data.error.

Contact.Servicing.

Tab. 8.5.1.8

Summary of Contents for PA8506-V





































































Reviews:

No comments