manualshive.com logo in svg

Paso PA8506-V, Instructions For Use Manual, Page: 59 / 68

Share
Download
Paso PA8506-V Instructions For Use Manual Download Page 59

55

System Manual | 2014

PA8500-VES | Voice Evacuation System 

UK

PA8506-V 

|

 VES Compact System

8.8.1 

Activation of an Automatic Emergency:

In. the. event. of. activation. of. a. programmed. local. input. contact,. the. PA8506-V.

system. will. suspend. its. normal. activity. typical. of. the. “Quiescent. condition”,. stop.

the.music.being.broadcast,.inhibit.the.functions.of.the.PA.sources.for.broadcasting.

announcement.and.show.the.“CONTROL.INPUT.STATUS”.panel.

If.the.contact.has.been.programmed.to.send.at.least.one.emergency.message.to.at.

least.one.output.zone,.the.system.will.initiate.the.Automatic.Emergency.by.enabling.

a.“Voice.Alarm.Condition”.and.causing.the.ALARM.LED.to.light.up..The.display.will.

therefore.show.a.list.of.all.the.active.inputs.(whether.programmed.or.otherwise).and.

will.indicate.the.type.of.pre-recorded.message.on.the.outputs.for.each.zone.

If.the.contact.has.been.programmed.for.a.GENERAL.RESET,.the.system.will.start.

the.Automatic.Emergency.and.show.the.“CONTROL.INPUT.STATUS”.panel,.leaving.

the.ALARM.LED.extinguished.

8.8.2 

Operation of the system during Automatic Emergency

-. As.long.as.the.input.contacts.are.active,.the.MUSIC.panel.will.remain.inactive..It.will,.however,.be.possible.to.navigate.among.the.various.menus.to.

access.the.advanced.functions.of.the.system.and.to.investigate.or.change.the.settings.

.

•.Press.the.ESC.key.

To.access.the.MAIN.page.and.inspect.the.other.management.menus.

-. A. current. “Voice.Alarm. Condition”. due. to. an.Automatic. Emergency. may. be. altered. by. an. authorised. operator. entering. the. system. to. activate. the.

manual.controls.for.managing.the.emergency,.in.order.to.RESET.the.messages,.change.the.current.messages.or.send.live.announcements.using.the.

microphone.provided.for.this.purpose.

For.details.about.management.of.a.Manual.Emergency,.consult.the.MANUAL.EMERGENCY.Section,.point.8.9.

•.

Exiting from an Automatic Emergency:

.

•.De-activate.all.the.contacts.of.the.external.peripheral.unit.

In.order.to.signal.the.operator.that.an.activation.has.occurred.by.external.contacts,.the.system.maintains.the.INPUT.STATUS.CONTROL..status.display.

panel.(input.with.no.contact.and.no.zone.alarm.activated).
.

•.Press.the.ESC.key.

The.system.will.return.to.a.Quiescent.condition,.showing.the.MUSIC.panel.

8.8 

AUTOMATIC EMErGENCy - Alarm Condition activated from an external peripheral unit

Following.is.a.description.of.the.operating.mode.of.the.system.in.the.event.of.an.Automatic.Emergency.initiated.by.an.external.peripheral.unit.

activating.the.input.contacts.programmed.to.enable.a.“Voice.Alarm.Condition”.

Viewing the operational status:

ALARM.LED:.This.LED.lights.up.to.indicate.that.a.VOICE.ALARM.is.active.when.a.live.microphone.announcement.or.a.pre-recorded.message.

are.being.sent.out.to.at.least.one.zone..In.a.12-zone.system,.the.ALARM.LED.will.light.up.on.both.PA8506-V.units,.regardless.of.the.active.output.

zone.

display

:

In.proper.operating.conditions.with.a.dual.channel,.the.display.will.show.t.he.number.of.contacts.activated,.as.illustrated.in.the.figure..In.the.event.

of.a.failure.of.an.amplifier,.on.the.other.hand,.the.display.will.show.the.following.message:

“Only.one.channel.available.-.FAULT.CONDITION”.to.indicate.operation.on.a.single.channel.

Zone status bar:

-.

Empty label

:.zone.without.any.current.message

-.

rESET: 

zone.mute.due.to.general.reset.contact

-.

EVAC

:.zone.with.EVACUATION.message.being.broadcast

-.

ALErT

:.zone.with.ALERT.message.being.broadcast

-.

dIS

:.zone.in.which.alarms.are.disabled.(see.point.8.6.4)

-.

FAIL

:.zone.with.failure.condition.on.the.speaker.line..Label.shown.even.if.the.type.or.failure.does.not.prejudice.the.outgoing.signal..When.

operating.on.a.single.channel.due.to.an.amplifier.failure,.this.indicates.that.the.zone.is.unable.to.broadcast.the.planned.signal..For.details.see.

points.9.2.and.9.3.

For.details.about.the.messages.displayed,.consult.point.8.5.3.INSPECTION/CONTROL.INPUT.STATUS.and.for.details.about.programming.

consult.point.8.6.1.OPERATOR/Set>.CONTROL.INPUTS.

Summary of Contents for PA8506-V





































































Reviews:

No comments