manualshive.com logo in svg

Paso PA8506-V, Instructions For Use Manual, Page: 48 / 68

Share
Download
Paso PA8506-V Instructions For Use Manual Download Page 48

44

PA8506-V 

|

 VES Compact System

PA8500-VES | Voice Evacuation System 

System Manual | 2014

UK

8.6.3 

BACKGrOUNd TEST

.

Setting the background tests

Panel.for.enabling.and.disabling.background.testing.of.the.critical.sources.

affecting.the.ability.of.the.system.to.function.in.emergency.conditions..The.

categories. for. choosing. the. items. subjected. to. diagnostics. are. listed. as.

shown.in.the.figure.opposite.
•.. The.categories.for.choosing.the.items.subjected.to.diagnostics.are.listed.

as.shown.in.the.figure.opposite.

. >.2-Voice.Alarms.

see.point.8.6.3.1

. >.3-Amplifiers.

see.point.8.6.3.2

. >.4-Power.Supply. see.point.8.6.3.3

. >.6-Communication. see.point.8.6.3.4
or

press.ESC.to.return.to.the.OPERATOR.panel.

8.6.3.1  VOICE ALArM TEST

 

Setting the Test for Emergency Sources

Panel. for. enabling. and. disabling. background. testing. of. the. “Hand-held.

Emergency.Microphone”.and.the.“Manual.Emergency.Access.Key”.
•. Press.the.appropriate.numerical.key.to.enable.or.disable.the.

diagnostic.test:

>.1-Fire.Microphone:.

on

.(test.enabled).-.

off 

(test.disabled)

>.2-Evac.Message:.

on

.(test.enabled).-.

off 

(test.disabled)

>.3-Alert.Message:.

on

.(test.enabled).-.

off 

(test.disabled)

>.5-Emerg..Button:.

on

.(test.enabled).-.

off 

(test.disabled)

>.6-Remote.Link:.

on

.(test.enabled).-.

off 

(test.disabled)

Note:.The.display.will.show.the.programming.that.has.been.set.

Press.ESC.to.return.to.the.BACKGROUND.TEST.panel.

8.6.3.2  AMPLIFIEr TEST 

 

Setting the tests for the Amplifiers

Panel.for.enabling.and.disabling.background.testing.of.the.internal.“Voice”.and.

“Music”.amplifiers,.of.the.“External”.amplifier.and.of.the.circuit.for.checking.

insulation.of.the.lines.with.regard.to.dispersion.to.earth.(GND.Fault)..
•...Press.the.appropriate.numerical.key.to.enable.or.disable.the.diagnostic.

test:

>.1-Test.voice.amp.:.

on

.(test.enabled).-.

off 

(test.disabled)

>.2-Test.music.amp:.

on

.(test.enabled).-.

off 

(test.disabled)

>.3-Test.ext..amp:.

on

.(test.enabled).-.

off 

(test.disabled)

>.6-Test.gnd.fault:..

on

.(test.enabled).-.

off 

(test.disabled)

Note:.The.display.will.show.the.programming.that.has.been.set.

Press.ESC.to.return.to.the.BACKGROUND.TEST.panel.

8.6.3.3  POWEr SUPPLy TEST

 

Setting the test for the Power Supplies

Panel. for. enabling. and. disabling. background. testing. of. the. primary. 230.

VAC.power.supply,.the.secondary.24.VDC.power.supply.and.the.memory.

for.managing.the.display.
•.. Press.the.appropriate.numerical.key.to.enable.or.disable.the.diagnostic.

test:

.>.1-Main.P.S.:..

on

.(test.enabled).-.

off 

(test.disabled)

>.2-24Vdc.P.S.:.

on

.(test.enabled).-.

off 

(test.disabled)

>.6-Display:..

on

.(test.enabled).-.

off 

(test.disabled)

Note:.The.display.will.show.the.programming.that.has.been.set.

Press.ESC.to.return.to.the.BACKGROUND.TEST.panel.

Summary of Contents for PA8506-V





































































Reviews:

No comments