14. Scroll right until “Function List” is highlighted(on screen 2/2) then click on “Function List”
once.
15. Scroll right to highlight “Travel Adjust” and click once.
16. With the transmitter throttle(altitude) stick in the down position scroll to highlight
“Throttle” and click once. Scroll until it shows 100%. Lift the throttle(altitude) stick up and
scroll until it shows 100%. Click once to save your setting.
17. Scroll right and click on “Aileron”, scroll until it reads 50%. Hold the “Aileron” stick to the
left and scroll until it reads 50%. Click once to save your setting.
18. Click on “Elev” and scroll until it reads 50%, then hold the “Elev”(Pitch) stick in the down
position and scroll until it reads 50%. Click once to save the setting.
19. Click on “Gear” and set it to 25%. Toggle the “Gear Switch” to the “0” position and set to
25%. Click once to save the setting.
Binding Instructions
General Instructions for Binding your Transmitter and Receiver
1. Plug one of the ESC Signal Cables into the throttle (THRO) jack on your receiver. Be
careful to connect the wire in the correct orientation. There will be a symbol such as “^ +
–” to indicate orientation, where ^ corresponds to the white signal wire, + corresponds to
the red positive wire, and – corresponds to the black negative wire.
2. Insert the bind plug supplied with your receiver into the bind (BND/DAT) jack on your
receiver.
3. Follow the binding instructions supplied with your transmitter or receiver.
Instructions for Binding a
Spektrum
Transmitter and Receiver
1. Plug one of the ESC Signal Cables into the throttle (THRO) jack on your receiver. Be
careful to connect the wire in the correct orientation. There will be a symbol such as “^ +
–” to indicate orientation, where ^ corresponds to the white signal wire, + corresponds to
the red positive wire, and – corresponds to the black negative wire.
2. Insert the bind plug supplied with your receiver into the bind (BND/DAT) jack on your
receiver.
3. Make sure your transmitter is switched
off
and the throttle is all the way down.
4. Plug the battery into the Power Harness to provide power to the ELEV-8. The LED in the
receiver should be flashing rapidly.
5. Locate the "Trainer/Bind" switch/button on your receiver. Hold the switch in the "1"
position / depress the button while turning on the transmitter. Continue holding until the
LED on the receiver stops flashing. (You may need to be at least 6 feet (2m) away from
the receiver).
6. Unplug the battery,
remove the bind plug
, and turn off your transmitter.
Copyright © Parallax Inc.
ELEV-8 V2 Assembly Guide
07/26/2018
Summary of Contents for ELEV-8 V2
