Paradyne COMSPHERE 6800 Series Page 204 Command Reference Manual Download

Page: 204 / 237

Modem/DSU Commands

2-181

6800-A2-GB31-20

January 1997

Store Call Detail Data (Required field)

Specify whether or not call detail information should be stored.

Valid entries are yes (default) or no. If no is selected, the following message is displayed:

Entering no entry in the Store call detail data field causes the 6800 NMS to stop
gathering call details.

A pop-up menu is available listing valid selections.

Call Statistics Available From (Display field)

Displays the earliest date for which summary information is stored.

Call Detail Available From (Display field)

Displays the earliest date for which call detail information is stored.

Number of local 3800 Series modems (Display field)

Displays the number of local 3800 Series modems for which call statistics are being
retrieved and stored.

Manage Call Statistics Results Form

The results form displays a text message indicating whether or not call statistics parameters have
been updated.

Summary of Contents for COMSPHERE 6800 Series














































































































































































































































Search results

Summary of Contents for COMSPHERE 6800 Series

Reviews:

Related manuals for COMSPHERE 6800 Series

Brands by name

Popular brands

Paradyne COMSPHERE 6800 Series, Command Reference Manual

Search results

Summary of Contents for COMSPHERE 6800 Series

Reviews:

Related manuals for COMSPHERE 6800 Series

Brands by name

Popular brands