manualshive.com logo in svg

Paradyne COMSPHERE 6800 Series, Command Reference Manual

The Paradyne COMSPHERE 6800 Series is a cutting-edge telecommunications product designed to revolutionize connectivity. Our comprehensive manual provides step-by-step Installation and Enabling/Disabling Instructions, allowing users to seamlessly set up and configure the device. Download this manual for free from our website to unlock the full potential of your Paradyne COMSPHERE 6800 Series.

Share
Download
background image

COMSPHERE 6800 Series Network Management System

2-150

January 1997

6800-A2-GB31-20

EIA Status (eias)

Use the eias command to display the status of EIA interface leads on a COMSPHERE
3400/4400 Series modem or a COMSPHERE 3600 Series DSU, a COMSPHERE 3800 Series
modem, or a DATAPHONE II APL modem, DDD modem, or 2700 Series DSU.

The eias command will also report the V.35 status of a 3600 Series DSU or a 3800 Series modem.
The DSU can be optioned for either a V.35 or an EIA-RS232 or RS366 interface. The V.35
interface supports speeds of up to 64 kbps and is typically used to connect the DSU to a front-end
processor. Regardless of the interface type, the leads that are supported are identical. For most
commands, NMS enables you to specify the destination for the command’s results and schedule its
execution. If the last page of the input form cannot accommodate the Destination for results and
Schedule execution fields, an additional page is provided. For a complete description of these
fields, refer to Chapter 1, Introduction.

Access Level:

Help Desk, Data Technician, Manager, System Administrator

Abbreviation:

eias 
Alternate: eia

Restrictions:

None

Routine:

Yes

Schedule:

Yes

Related Commands: None

EIA Status Input Form

This input form contains the following field:

Device(s) (Required field)

Enter the device(s) whose EIA interface leads states will be displayed. One or more
devices may be specified. Standard addressing format applies to the input. For
information on device addressing, refer to Appendix D of the COMSPHERE 6800 Series
Network Management System User’s/System Administrator’s Guide.

EIA Status Results Form

A separate results form is displayed for each device specified. Each results form lists device
information for the specified device, the applicable set of leads, and the status of each lead.
Figure 2-46 and Figure 2-47 are Page 1 and Page 2 of a sample EIA Status results form for a
COMSPHERE 3800 Series modem.

Summary of Contents for COMSPHERE 6800 Series














































































































































































































































Reviews:

No comments

Related manuals for COMSPHERE 6800 Series

Patton electronics 1007 User Manual preview
1007
Brand: Patton electronics Pages: 5
Racelogic NTRIPMDM-V1 Quick Start Manual preview
NTRIPMDM-V1
Brand: Racelogic Pages: 7
i-mate JASJAR Manuallines For Use preview
JASJAR
Brand: i-mate Pages: 7
Maestro 100EVO SERIES Quick Start Manual & User Manual preview
100EVO SERIES
Brand: Maestro Pages: 32
Multitech MTD100U User Manual preview
MTD100U
Brand: Multitech Pages: 36
Siemens SpeedStream 4200 Quick Start Manual preview
SpeedStream 4200
Brand: Siemens Pages: 8
Siemens EDGE Speed ES75 Installation Manual preview
EDGE Speed ES75
Brand: Siemens Pages: 4
Siemens SpeedStream 4100 Instructions Manual preview
SpeedStream 4100
Brand: Siemens Pages: 9
Siemens APOGEE USR5686 Installation Instructions preview
APOGEE USR5686
Brand: Siemens Pages: 2
Siemens tc35it Installation & Programming Manual preview
tc35it
Brand: Siemens Pages: 16
Siemens Orcon Homehub Installation Manual preview
Orcon Homehub
Brand: Siemens Pages: 20
Siemens Gigaset SX685 WiMAX Quick Start Manual preview
Gigaset SX685 WiMAX
Brand: Siemens Pages: 32
Siemens SITRANS TK Operating Instructions Manual preview
SITRANS TK
Brand: Siemens Pages: 56
Siemens C2-010 User Manual preview
C2-010
Brand: Siemens Pages: 51
Siemens SIMATIC NET MODEM MD720 System Manual preview
SIMATIC NET MODEM MD720
Brand: Siemens Pages: 67
Siemens Gigaset USB Stick 54 Quick Start Manual preview
Gigaset USB Stick 54
Brand: Siemens Pages: 70
Siemens SINAUT MD720-3 System Manual preview
SINAUT MD720-3
Brand: Siemens Pages: 76
Siemens Insys 56k Operating Manual preview
Insys 56k
Brand: Siemens Pages: 84

Brands by name

Popular brands

Load more brands