manualshive.com logo in svg

Paradyne COMSPHERE 6800 Series, Command Reference Manual

The Paradyne COMSPHERE 6800 Series is a cutting-edge telecommunications product designed to revolutionize connectivity. Our comprehensive manual provides step-by-step Installation and Enabling/Disabling Instructions, allowing users to seamlessly set up and configure the device. Download this manual for free from our website to unlock the full potential of your Paradyne COMSPHERE 6800 Series.

Share
Download
background image

2

Modem/DSU Commands

2-69

6800-A2-GB31-20

January 1997

Access Level:

Data Technician, Manager, System Administrator

Abbreviation:

chpm

Restrictions:

The new link level address that results from a protocol mode change is not 
reflected in existing routines, scheduled commands, trouble tickets, alerts, 
or automatic trouble reports that were issued before the device’s protocol 
mode was changed. The records will be keyed to the device’s old address.

This command can be canceled within a 10-second interval after execution.
After ten seconds, the command cannot be canceled.

Before executing this command, be sure there are no active alerts on the 
local control device or on the circuit.

Before executing this command, be sure there are no devices in test mode. 
If there are, abort the test or wait until the test is completed before 
executing the chpm command.

Routine:

No

Schedule:

No

Related Commands: None

Change Protocol Mode Input Form

The Change Protocol Mode input form contains the following fields:

Device (Required field)

Enter the device whose protocol mode is to be changed. Standard addressing format
applies. For information on device addressing, refer to Appendix D of the COMSPHERE
6800 Series Network Management System User’s/System Administrator’s Guide.

Protocol mode (Required field)

To change to ADp mode, enter advanced.

To change to DPII mode, enter dpII.

A pop-up menu is available listing valid selections.

Set CCN event

If configuration change notification has been enabled for this device, use this field to
determine whether or not this particular configuration change will be reported to the
NMS.

Enter yes to report this change to the NMS.

Enter no (default) to prevent this change from being reported to the NMS.

If configuration change notification has been disabled for this device, configuration
changes are not reported to the NMS regardless of what is entered in this field. A pop-up
menu is available listing valid selections.

Summary of Contents for COMSPHERE 6800 Series














































































































































































































































Reviews:

No comments

Related manuals for COMSPHERE 6800 Series

Data-Linc Group PlantLinc PLR5000 User Manual preview
PlantLinc PLR5000
Brand: Data-Linc Group Pages: 31
3Com HomeConnect 3CP4130 User Manual preview
HomeConnect 3CP4130
Brand: 3Com Pages: 74
Zoom 2919 Specification Sheet preview
2919
Brand: Zoom Pages: 2
Zoom 2920 Specification Sheet preview
2920
Brand: Zoom Pages: 2
TCAM Tmas T61 Hardware User'S Manual preview
Tmas T61
Brand: TCAM Pages: 47
Paradyne Hotwire 6205 Installation Instructions Manual preview
Hotwire 6205
Brand: Paradyne Pages: 15
Franklin U601 User Manual preview
U601
Brand: Franklin Pages: 38
Speed Touch 330 Installation Manual preview
330
Brand: Speed Touch Pages: 6
Xircom 100Base-TX Specifications preview
100Base-TX
Brand: Xircom Pages: 4
Raymar Telenetics MIU14.4L User Manual preview
Telenetics MIU14.4L
Brand: Raymar Pages: 43
Altice UBC1326AA00 Quick Installation Manual preview
UBC1326AA00
Brand: Altice Pages: 4
ADTRAN 1200861L1 Quick Start Manual preview
1200861L1
Brand: ADTRAN Pages: 2
ADTRAN 1203153L2 User Manual preview
1203153L2
Brand: ADTRAN Pages: 146
E-Drive Technology RF-Modem II User Manual preview
RF-Modem II
Brand: E-Drive Technology Pages: 9
ND SatCom SKYWAN IDU 1070 Manual preview
SKYWAN IDU 1070
Brand: ND SatCom Pages: 154
D-Link DCM-200 Manual preview
DCM-200
Brand: D-Link Pages: 12
Maestro 100 CDMA Quick Start Manual & User Manual preview
100 CDMA
Brand: Maestro Pages: 21
GE e-terrapowercom Installation Manual preview
e-terrapowercom
Brand: GE Pages: 30

Brands by name

Popular brands

Load more brands