manualshive.com logo in svg

Paradyne COMSPHERE 6800 Series, Command Reference Manual

The Paradyne COMSPHERE 6800 Series is a cutting-edge telecommunications product designed to revolutionize connectivity. Our comprehensive manual provides step-by-step Installation and Enabling/Disabling Instructions, allowing users to seamlessly set up and configure the device. Download this manual for free from our website to unlock the full potential of your Paradyne COMSPHERE 6800 Series.

Share
Download
background image

COMSPHERE 6800 Series Network Management System

2-120

January 1997

6800-A2-GB31-20

Figure 2-33. Display Alert Information Results Form

DATAPHONE II 2700 Series DSUs with active facility failures (FA alerts) display one or more of
the following messages:

•

The set is intermittently out of frame.

•

The set is continuously out of frame.

•

Abnormal Station network control code is being received.

•

No signal is being received by the receiver LSI.

•

Control Mode Idle code is being sent to set with no E2 option.

•

Unrecognized network control code is being received.

•

Out of Service 1 network control code is being received.

•

Out of Service 2 network control code is being received.

•

Out of Service 3 network control code is being received.

•

There are no facility faults for this modem.

Summary of Contents for COMSPHERE 6800 Series














































































































































































































































Reviews:

No comments

Related manuals for COMSPHERE 6800 Series

Multitech SocketModem MT2456SMI-22 Developer'S Manual preview
SocketModem MT2456SMI-22
Brand: Multitech Pages: 58
Ericsson GC 75 Preliminary User Manual preview
GC 75
Brand: Ericsson Pages: 26
B&B Electronics Zlinx Xtreme IP67 ZXT9-RM Instruction Manual preview
Zlinx Xtreme IP67 ZXT9-RM
Brand: B&B Electronics Pages: 164
ATO CMM 900-3W User Manual preview
CMM 900-3W
Brand: ATO Pages: 18
Radyne DMD2401 LB Installation And Operation Manual preview
DMD2401 LB
Brand: Radyne Pages: 179
TeleWell TW-EA210 User Manual preview
TW-EA210
Brand: TeleWell Pages: 131
MikroTik R11e-LTE Quick Start Manual preview
R11e-LTE
Brand: MikroTik Pages: 8
KWorld DVB-T 323U Faq preview
DVB-T 323U
Brand: KWorld Pages: 21
GDI FDM-FSK User Manual preview
FDM-FSK
Brand: GDI Pages: 49
LG Innotek LTD-BH1000 User Manual preview
LTD-BH1000
Brand: LG Innotek Pages: 36
Paradyne COMSPHERE 3920PLUS Series Specifications preview
COMSPHERE 3920PLUS Series
Brand: Paradyne Pages: 2
Ebyte E34-DTU User Manual preview
E34-DTU
Brand: Ebyte Pages: 17
Ebyte 2G4HD12 User Manual preview
2G4HD12
Brand: Ebyte Pages: 24
Ebyte E180-DTU User Manual preview
E180-DTU
Brand: Ebyte Pages: 35
Ebyte 400SL22P User Manual preview
400SL22P
Brand: Ebyte Pages: 35
Paradyne COMSPHERE 3810Plus Quick Reference preview
COMSPHERE 3810Plus
Brand: Paradyne Pages: 28
Eurotech ZyWAN-G9 Quick Start preview
ZyWAN-G9
Brand: Eurotech Pages: 2
Enfora GPRS User Manual preview
GPRS
Brand: Enfora Pages: 23

Brands by name

Popular brands

Load more brands