manualshive.com logo in svg

Paradyne COMSPHERE 6800 Series, Command Reference Manual

The Paradyne COMSPHERE 6800 Series is a cutting-edge telecommunications product designed to revolutionize connectivity. Our comprehensive manual provides step-by-step Installation and Enabling/Disabling Instructions, allowing users to seamlessly set up and configure the device. Download this manual for free from our website to unlock the full potential of your Paradyne COMSPHERE 6800 Series.

Share
Download
background image

COMSPHERE 6800 Series Network Management System

2-112

January 1997

6800-A2-GB31-20

Duration of test (ddd)

This field is applicable only for DATAPHONE II DDD modems. If you are testing a
DATAPHONE II DDD modem, enter the test duration. The only valid entry is 
120 seconds.

A pop-up menu is available listing valid selections.

Port number (Required field)

Specify the number of the port on the device from which the test will be run.

•

For 3400/4400 Series modems, valid entries are from 1 through 4.

•

For 3600 Series devices, valid entries are from 1 through 6, or a (for aggregate).
Selecting a causes the test to be run between two DSU transmitters/receivers
rather than between two ports on the TDMs.

•

For DATAPHONE II devices, the only valid entry is 1.

A pop-up menu is available listing valid selections. Default = 1.

Digital Test Results Form

Different results forms are displayed according to the device specified in the input form.

Figure 2-30 is a sample results form for DATAPHONE II APL modems.

Figure 2-30. Digital Test Results Form for DATAPHONE

 II APL Modems

Summary of Contents for COMSPHERE 6800 Series














































































































































































































































Reviews:

No comments

Related manuals for COMSPHERE 6800 Series

ICP DAS USA GTM-200M User Manual preview
GTM-200M
Brand: ICP DAS USA Pages: 38
Tenda TED8620R User Manual preview
TED8620R
Brand: Tenda Pages: 29
Patton electronics NetLink 1095 User Manual preview
NetLink 1095
Brand: Patton electronics Pages: 20
Patton electronics NetLink 1094A User Manual preview
NetLink 1094A
Brand: Patton electronics Pages: 17
Patton electronics 1088/I User Manual preview
1088/I
Brand: Patton electronics Pages: 13
Fargo Maestro 100 User Manual preview
Maestro 100
Brand: Fargo Pages: 17
Westridge Communications DIRECT CONNECT MODEM 6420 Addendum To Operating Manual preview
DIRECT CONNECT MODEM 6420
Brand: Westridge Communications Pages: 8
TP-Link TD-W8960N Installation Manual preview
TD-W8960N
Brand: TP-Link Pages: 24
2Wire i38HG User Manual preview
i38HG
Brand: 2Wire Pages: 108
zBoost SOHO YX560P User Manual preview
SOHO YX560P
Brand: zBoost Pages: 11
Paradyne Comsphere User Manual preview
Comsphere
Brand: Paradyne Pages: 125
3Com 005689-03 Installation Manual preview
005689-03
Brand: 3Com Pages: 2
3Com OfficeConnect 3C891A Release Note preview
OfficeConnect 3C891A
Brand: 3Com Pages: 24
3Com HomeConnect Getting Started Manual preview
HomeConnect
Brand: 3Com Pages: 70
OutdoorRouter WRT2 Instruction Manual preview
WRT2
Brand: OutdoorRouter Pages: 8
ADB P.DG A4001N User Manual preview
P.DG A4001N
Brand: ADB Pages: 108
Franklin Wireless U210 User Manual preview
U210
Brand: Franklin Wireless Pages: 35
US Robotics 002605-00 - Installation Manual preview
002605-00 -
Brand: US Robotics Pages: 152

Brands by name

Popular brands

Load more brands