Paradyne COMSPHERE 6800 Series Page 112 Command Reference Manual Download | Manualshive

Page: 112 / 237

background image

2

Modem/DSU Commands

2-89

6800-A2-GB31-20

January 1997

Configuration Change Notification (ccn)

Use the ccn command to display the configuration events that have occurred on a COMSPHERE
device. You can also use this command to clear the memory area in the device where the
configuration events are stored.

For most commands, NMS enables you to specify the destination for the command’s results and
schedule its execution. If the last page of the input form cannot accommodate the Destination for
results and Schedule execution fields, an additional page is provided. For a complete description
of these fields, refer to Chapter 1, Introduction.

Access Level:

Help Desk, Data Technician, Manager, System Administrator

Abbreviation:

ccn

Restrictions:

None

Routine:

Yes

Schedule:

Yes

Related Commands: Configuration Change Notification Enable/Disable (ccned)

Configuration Change Notification Input Form

The Configuration Change Notification input form contains the following fields:

Device(s) (Required field)

Enter the device(s) whose configuration changes will be displayed. One or more devices
may be specified. Standard addressing format applies to the input. For information on
device addressing, refer to Appendix D of the COMSPHERE 6800 Series Network
Management System User’s/System Administrator’s Guide.

Test state (Required field)

Enter display to display configuration events for the device(s) specified.

Enter clear to display the configuration events for the specified device(s), and then clear
memory.

A pop-up menu is available listing valid selections.

«
...
110
111
112
113
114
...
»

Summary of Contents for COMSPHERE 6800 Series














































































































































































































































Reviews:

No comments

Related manuals for COMSPHERE 6800 Series

Brand: Multitech Pages: 80

Brand: XtendLan Pages: 73

Brand: CalAmp Pages: 102

Brand: NAPCO Pages: 16

Brand: Sangamo Pages: 66

Brand: Dynex Pages: 2

Brand: Zte Pages: 68

Brand: GDI COMMUNICATIONS Pages: 21

Brand: GDI Pages: 21

Brand: WM Systems Pages: 28

Wi-Fi 4G Advanced Pro X

Brand: Telstra Pages: 17

WI-FI 4G ADVANCED II

Brand: Telstra Pages: 22

Brand: Telstra Pages: 31

Wi-Fi 4G Advanced

Brand: Telstra Pages: 44

Brand: SMC Networks Pages: 100

Brand: Radio Shack Pages: 8

Brand: Radio Shack Pages: 40

Brand: Zte Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands