manualshive.com logo in svg

Paradyne COMSPHERE 6800 Series, Command Reference Manual

The Paradyne COMSPHERE 6800 Series is a cutting-edge telecommunications product designed to revolutionize connectivity. Our comprehensive manual provides step-by-step Installation and Enabling/Disabling Instructions, allowing users to seamlessly set up and configure the device. Download this manual for free from our website to unlock the full potential of your Paradyne COMSPHERE 6800 Series.

Share
Download
background image

COMSPHERE 6800 Series Network Management System

1-12

January 1997

6800-A2-GB31-20

monthly

Causes the command to execute on a monthly basis. When you enter monthly into the
Schedule execution field, the system displays the following fields:

Day(s) of the month

Enter the day(s) of the month when this command is to execute. Valid entries are
as follows:

•

Multiple days. The numbers must be separated by commas or spaces,
e.g., 1,4,7,10.

•

A range of days, e.g., 8-15.

•

The keyword last to execute the command on the last day of the current
month.

•

The keyword all to execute the command each day of the current
month.

Time(s)

Enter the time(s) the command is to execute for each day specified. For time(s)
format, refer to the Time(s) field explanation for delayed command execution.

Last date

Enter the stop date for execution of the command. If you leave this field blank,
the command will execute on a monthly basis indefinitely. The last date must
occur after the first scheduled date.

For date entry parameters refer to the Date(s) field explanation for delayed
command execution.

Results Forms

Each modem/DSU command is associated with one or more results forms. Depending on the
command issued, the results form(s) can display a success or failure message for command
execution, reflect the changes made for a device as a result of the command execution, and display
detailed information (e.g., health and status statistics) for the specified device(s). A results form
trailer message indicates start and stop times for command execution. Figure 1-3 shows an
example of a results form for the Circuit Loss Inbound (cli) command, which is used to measure
the inbound circuit loss to a specified COMSPHERE APL modem or DATAPHONE II APL device
from an associated tributary. The results form for this command reflects the tone frequency
specified and the decibel (dB) level of the inbound signal loss for the device(s) specified.

Summary of Contents for COMSPHERE 6800 Series














































































































































































































































Reviews:

No comments

Related manuals for COMSPHERE 6800 Series

Sel SEL-9192 Manual preview
SEL-9192
Brand: Sel Pages: 16
ADF Web HD67302-B2 Series User Manual preview
HD67302-B2 Series
Brand: ADF Web Pages: 20
SAGEMCOM Sunrise Internet Box User Manual preview
Sunrise Internet Box
Brand: SAGEMCOM Pages: 2
Draytek Vigor130 User Manual preview
Vigor130
Brand: Draytek Pages: 288
Aztech 56K PCI Modem Manual preview
56K PCI Modem
Brand: Aztech Pages: 16
GE ActiveKEY User Manual preview
ActiveKEY
Brand: GE Pages: 5
Honeywell E-Mon E10039 Installation And Setup Manual preview
E-Mon E10039
Brand: Honeywell Pages: 36
Honeywell CLOUDLINK 4G M1 Quick Start preview
CLOUDLINK 4G M1
Brand: Honeywell Pages: 4
Honeywell Cloud Link 4G Modem User Manual preview
Cloud Link 4G Modem
Brand: Honeywell Pages: 71
Honeywell Fire-Lite 2UD Mounting Instructions preview
Fire-Lite 2UD
Brand: Honeywell Pages: 2
HP p5091a Installation Manual preview
p5091a
Brand: HP Pages: 14
HP J8135A Quick Install Manual preview
J8135A
Brand: HP Pages: 30
HP D7808A User Manual preview
D7808A
Brand: HP Pages: 50
4G Systems XSStick W14 Quick Start Manual preview
XSStick W14
Brand: 4G Systems Pages: 2
Zoom 1064 Series User Manual preview
1064 Series
Brand: Zoom Pages: 61
Buenoptic HFB-FO-LON Series Data Sheet & User Manual preview
HFB-FO-LON Series
Brand: Buenoptic Pages: 8
Four-Faith F214-E Series User Manual preview
F214-E Series
Brand: Four-Faith Pages: 34
Sulzer CA 524 Installation Manual preview
CA 524
Brand: Sulzer Pages: 8

Brands by name

Popular brands

Load more brands