Paradyne COMSPHERE 6800 Series Command Reference Manual Download | Manualshive

Page: 39 / 237

background image

COMSPHERE 6800 Series Network Management System

2-16

January 1997

6800-A2-GB31-20

REPORT PERIOD

Enter a report period for generation of the report. The report will include call statistics
from the starting date to the ending date specified.

Date(s) included

Enter a starting date and an ending date for call statistics information to be
reported.

The valid format for the starting date is mm/dd/yy. The default is the previous
day’s date.

The valid format for the ending date is mm/dd/yy. The default is the previous
day’s date.

An error message displays if the specified start and end dates result in an invalid
range of dates. There are three possible errors, as follows:

•

Start date is less than earliest available date

•

End date is greater than latest available date

•

Start date is greater than end date

Call statistics available from (Display field)

Displays the earliest call statistics record found in the database.

Call statistics available until (Display field)

Displays the latest call statistics record found in the database.

Day(s) included

Enter the days of the week for which this report will be generated.

Valid entries are as follows: one or more individual days (mon, tue, wed, thu,
fri, sat, sun), a range of days (e.g., mon-thu), or the keyword all (default).

Threshold

Specify the number of calls to be used as a threshold value for this report. The
graphical results for this report changes the bar color from green to red wherever
the number of calls exceeds this threshold. The tabular results displays *** after
every value that exceeds the specified threshold value.

Valid entries are from 0 through 9999.

Title

Enter a title for this report.

Valid entries are any alphanumeric character string up to 40 characters in length.

«
...
37
38
39
40
41
...
»

Summary of Contents for COMSPHERE 6800 Series














































































































































































































































Reviews:

No comments

Related manuals for COMSPHERE 6800 Series

Brand: Falcon Pages: 36

Brand: Optelecom Pages: 26

Brand: ZyXEL Communications Pages: 385

Brand: Raveon Pages: 32

Brand: RadioLabs Pages: 11

Brand: Acer Pages: 82

Brand: HORNER Pages: 40

Brand: IFM Electronic Pages: 45

Brand: Four-Faith Pages: 22

Brand: Cradlepoint Pages: 137

Brand: 3Com Pages: 62

Brand: Lucent Technologies Pages: 80

Barricade SMC7904BRA2

Brand: SMC Networks Pages: 2

Brand: TP-Link Pages: 122

Brand: KBC Pages: 12

Brand: Maxis Pages: 63

Brand: Feeney Wireless Pages: 11

FireLine MURS band

Brand: Raveon Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands