Paradyne COMSPHERE 6800 Series Page 212 Command Reference Manual Download | Manualshive

Page: 212 / 237

background image

2

Modem/DSU Commands

2-189

6800-A2-GB31-20

January 1997

Receive Signal Spectrum (rss)
(Disruptive)

Use the rss command to measure the inbound received signal levels at various frequencies for a
COMSPHERE 3400/4400 Series modem. The control modem, tributary modem, and primary data
channel are affected when this test is run. This test will continue to run until the command is
executed again using the abort option, or until an Abort command (abort) is executed.

For most commands, NMS enables you to specify the destination for the command’s results and
schedule its execution. If the last page of the input form cannot accommodate the Destination for
results and Schedule execution fields, an additional page is provided. For a complete description
of these fields, refer to Chapter 1, Introduction.

Access Level:

Data Technician, Manager, System Administrator

Abbreviation:

rss

Restrictions:

The tributary modem that is selected must be directly connected to the
specified control modem.

Routine:

Yes

Schedule:

Yes

Related Commands: Abort (abort)

Receive Signal Spectrum Input Form

This input form contains the following fields:

Control Device (Required field)

Enter the control device to be involved in this test. Standard addressing format applies to
the input. For information on device addressing, refer to Appendix D of the
COMSPHERE 6800 Series Network Management System User’s/System Administrator’s
Guide.

Mode (Required field)

Enter one of the following test options:

start

Starts the receive signal spectrum test at the selected tributary modem.

abort

Stops the receive signal spectrum test.

display

Displays the receive signal spectrum test results while the test is in progress.

A pop-up menu is available listing valid selections.

«
...
210
211
212
213
214
...
»

Summary of Contents for COMSPHERE 6800 Series














































































































































































































































Reviews:

No comments

Related manuals for COMSPHERE 6800 Series

Brand: Paradyne Pages: 22

Brand: Black Box Pages: 101

Brand: Moultrie Mobile Pages: 7

Brand: Zte Pages: 27

Brand: Acanac Pages: 2

Brand: Thermo Scientific Pages: 37

Brand: Cermetek Pages: 19

Brand: Kasda Pages: 40

Brand: Kasda Pages: 41

Hotwire 6310 MVL

Brand: Paradyne Pages: 17

Brand: GDI COMMUNICATIONS Pages: 31

Brand: Spectrum Pages: 4

Brand: goTenna Pages: 92

Brand: Bausch Datacom Pages: 22

Brand: WiOn Pages: 8

Brand: Blink Pages: 4

Brand: Hughes Pages: 54

Brand: Elastic Networks Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands