manualshive.com logo in svg

Paradyne COMSPHERE 6800 Series, Command Reference Manual

Share
Download
Paradyne COMSPHERE 6800 Series Command Reference Manual Download Page 123

COMSPHERE 6800 Series Network Management System

2-100

January 1997

6800-A2-GB31-20

Page 1 for Subnetwork Devices

Figure 2-27 is a sample of the subnetwork Device Health and Status results form.

Figure 2-27. Device Health and Status Results Form for Subnetwork Devices

This results form lists the device information for each device tested and displays the following
information:

NAME

The names of each device tested.

ADDRESS

The addresses of each device tested.

NETWORK

The network name of each device tested.

STATUS

The current status of each device (alert abbreviations of the current abnormal status
conditions). If the addressed device has no abnormal status to report, the display reads
stat norm. For downstream devices with normal status, this information will not be
displayed.

Summary of Contents for COMSPHERE 6800 Series














































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands