Paradyne COMSPHERE 6800 Series Page 66 Command Reference Manual Download | Manualshive

Page: 66 / 237

background image

2

Modem/DSU Commands

2-43

6800-A2-GB31-20

January 1997

This input form contains the following fields:

Telephone Number

For each directory displayed, overwrite the existing telephone number or specify a new
number. For 3400/4400 Series modems equipped with a DBM, the following characters
can be used when specifying a telephone number:

0–9

Number

*

DTMF number *

#

DTMF number #

t

Tone dialing

p

Pulse dialing

w or +

Wait for dial tone

,

Pause

space or -

Separator for readability

0

Separator for readability

:

Delimiter for comment

Call

Specify a secondary directory whose telephone number entry will be used as the primary
backup number. Valid entries are from 1 through 4.

Strap

Specify a strap area to use when establishing a dial line. Valid entries are active, cust1,
cust2. A pop-up menu is available listing valid selections.

Set CCN event

If configuration change notification has been enabled for this device, use this field to
determine whether or not this configuration change will be reported to the NMS.

Enter yes to report this change to the NMS.

Enter no (default) to prevent this change from being reported to the NMS.

If configuration change notification has been disabled for this modem, configuration
changes are not reported to the NMS regardless of what is entered here.

A pop-up menu is available listing valid selections.

Change Call Directory Results Form

The results form displays device information for each specified device and indicates whether or not
the command was successful executed.

«
...
64
65
66
67
68
...
»

Summary of Contents for COMSPHERE 6800 Series














































































































































































































































Reviews:

No comments

Related manuals for COMSPHERE 6800 Series

Brand: Abocom Pages: 14

Brand: ADTRAN Pages: 57

Brand: SBC Pages: 32

Brand: KaiDeng Pages: 4

Brand: BROSTREND Pages: 13

Brand: Black Box Pages: 31

MDS932AE-10BT-R2

Brand: Black Box Pages: 29

Brand: Black Box Pages: 45

E95-DTU433L 485-V8 Series

Brand: Ebyte Pages: 19

Brand: NETGEAR Pages: 198

Brand: PROLiNK Pages: 10

USB ADSL Modem Hurricane Series

Brand: PROLiNK Pages: 21

Brand: Spytec Pages: 12

Brand: ICPDAS Pages: 6

Brand: Bausch Datacom Pages: 26

Brand: Redline Pages: 27

Brand: Unitronics Pages: 4

Brand: M2M Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands