Paradyne COMSPHERE 6800 Series Page 126 Command Reference Manual Download | Manualshive

Page: 126 / 237

background image

2

Modem/DSU Commands

2-103

6800-A2-GB31-20

January 1997

Speed test is executed

This field is applicable for DATAPHONE II DDD devices only.

Enter the speed at which the self-test is to be executed. Valid entries are current (the speed
at which the device is currently running), 300, 1200, 2400, 4800 or 9600 bits per second.

A pop-up menu is available listing valid selections.

Device Test Results Form

The Device Test results forms vary based on the device type specified for the test.

For 3400/4400 Series modems without DBM-V, the results form displays the outcome of the test as
pass or fail and the results of the test as incomplete or complete. The results forms for the
3600 Series DSUs and the 3900 Series modems are similar. For 3400/4400 Series modems
equipped with the DBM-V option, the test outcome is displayed for both the modem’s main CCA
and for the modem’s DBM-V. The results form of the COMSPHERE 3800 Series DDD modems is
identical to that of the COMSPHERE APL modems.

For DATAPHONE II APL modems, the results form displays the specified test, the outcome of the
test as pass or fail, and the state of the test as complete or intermediate.

For DATAPHONE II DDD modems, the results form displays the test speed, the outcome of the
test as pass or fail, and the state of the test as intermediate or complete.

For DATAPHONE II DSUs, the results form displays the outcome of the test as pass or fail and
the state of the test as incomplete or complete.

«
...
124
125
126
127
128
...
»

Summary of Contents for COMSPHERE 6800 Series














































































































































































































































Reviews:

No comments

Related manuals for COMSPHERE 6800 Series

Brand: Paradyne Pages: 2

Brand: iRZ Pages: 19

Brand: Moeller Pages: 4

Brand: ELTEX Pages: 6

Brand: AVM Pages: 28

Brand: Zte Pages: 2

Brand: Blonder tongue Pages: 20

Brand: Enfora Pages: 98

Brand: Technicolor Pages: 85

Comtrend CT-6382T

Brand: Teleconnect Pages: 6

DirecWay DW4020

Brand: Hughes Network Pages: 102

Brand: NETGEAR Pages: 2

DG834v2 - ADSL Modem Router

Brand: NETGEAR Pages: 143

Brand: Hamlet Pages: 62

Brand: Feeney Wireless Pages: 11

E90-DTU 900SL22-GPRS

Brand: Ebyte Pages: 20

Brand: Patton electronics Pages: 24

Brand: Cisco Pages: 74

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands