Paradyne COMSPHERE 6800 Series Page 32 Command Reference Manual Download | Manualshive

Page: 32 / 237

background image

2

Modem/DSU Commands

2-9

6800-A2-GB31-20

January 1997

Calibrate Tributary Transmitter (ctt)

Use the ctt command to cause a selected COMSPHERE 3400/4400 Series high-speed, multipoint
control modem to attempt to calibrate the pre-emphasis on a selected link-attached tributary
modem. For more information on the Calibrate Tributary Transmitter function, see the individual
device documentation.

For most commands, NMS enables you to specify the destination for the command’s results and
schedule its execution. If the last page of the input form cannot accommodate the Destination for
results and Schedule execution fields, an additional page is provided. For a complete description
of these fields, refer to Chapter 1, Introduction.

Access Level:

Data Technician, Manager, System Administrator

Abbreviation:

ctt

Restrictions:

None

Routine:

Yes

Schedule:

Yes

Related Commands: None

Calibrate Tributary Transmitter Input Form

The Calibrate Tributary Transmitter input form enables you to specify a control device(s) and the
tributary devices to be calibrated.

This input form contains the following fields:

Control device(s) (Required field)

Enter the control device(s) corresponding to the tributaries to be calibrated. One or more
devices may be specified. Standard addressing format applies to the input. For
information on device addressing, refer to Appendix D of the COMSPHERE 6800 Series
Network Management System User’s/System Administrator’s Guide.

Tributary device(s) (Required field)

Enter the tributary devices to be calibrated. One or more devices may be specified.
Standard addressing format applies to the input. You may also enter the keyword all to
specify all tributary devices on the control modem(s) poll list.

«
...
30
31
32
33
34
...
»

Summary of Contents for COMSPHERE 6800 Series














































































































































































































































Reviews:

No comments

Related manuals for COMSPHERE 6800 Series

RM356 - Router - EN

Brand: NETGEAR Pages: 2

Brand: BandLuxe Pages: 23

Brand: Kyocera Pages: 11

Brand: TC Communications Pages: 23

Brand: Kathrein Pages: 8

Brand: StarHub Pages: 10

Brand: Blonder tongue Pages: 12

Brand: Four-Faith Pages: 22

Brand: Paradyne Pages: 125

Brand: Cradlepoint Pages: 5

Brand: Vonage Pages: 112

SURFboard SB3100i

Brand: General Instrument Pages: 21

Brand: Guilin Feiyu Technology Pages: 9

Brand: IBM Pages: 35

Brand: ICPDAS Pages: 55

Brand: RCA Pages: 35

Brand: 3Jtech Pages: 50

Brand: Vololink Pages: 50

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands