manualshive.com logo in svg

Paradyne COMSPHERE 6800 Series, Command Reference Manual

The Paradyne COMSPHERE 6800 Series is a cutting-edge telecommunications product designed to revolutionize connectivity. Our comprehensive manual provides step-by-step Installation and Enabling/Disabling Instructions, allowing users to seamlessly set up and configure the device. Download this manual for free from our website to unlock the full potential of your Paradyne COMSPHERE 6800 Series.

Share
Download
background image

1

Introduction

1-9

6800-A2-GB31-20

January 1997

Display-only Fields

Certain fields display data, but do not allow you to enter new data or change the data displayed.
Display-only fields appear on the input forms without boxes or underlines.

Carried-over Fields

Some fields display information provided by the user on a previous form of the current command.
Carried-over fields may be display-only, or in some cases, may allow user input.

Common Fields on Input Forms – Destination for results and Schedule execution

Destination for results

Use this field to specify where NMS should send the results from the command
execution. Valid options are crt, remote, printer, lp, and queue. Multiple destinations can
be specified.

crt (default)

This selection causes the command results to display on your workstation screen.
When you specify the destination as crt, the command must be executed
immediately. It cannot be scheduled for a later time.

NOTE

When you specify crt, NMS does not allow any other command to
be accessed from the current window until execution of the current
command has completed. Certain commands, e.g., tests that take
time to execute, or reports that include large volumes of data, can
take several minutes to complete. In these instances it is
recommended that you send the results of the command to a queue
or to a printer. The command will execute in the background,
allowing you to access and execute other commands at the same
time.

remote

This selection sends the results of the command to a remotely located printer. If
you specify remote, a telephone number prompt displays on the screen allowing
you to specify the telephone number of the remote printer. If an ACU phone
number has been included in your user profile (an optional field), this phone
number becomes the default number.

lp

Sends results to a remote line printer. You are prompted for the name of the
remote printer in a field that appears below the destination field.

Summary of Contents for COMSPHERE 6800 Series














































































































































































































































Reviews:

No comments

Related manuals for COMSPHERE 6800 Series

Paradyne COMSPHERE 3810 Hardware Manual preview
COMSPHERE 3810
Brand: Paradyne Pages: 2
Paradyne COMSPHERE 3800PLUS Manual preview
COMSPHERE 3800PLUS
Brand: Paradyne Pages: 7
Paradyne COMSPHERE 3810 Firmware Update Manual preview
COMSPHERE 3810
Brand: Paradyne Pages: 10
Paradyne BitStorm 6200 Installation Instructions preview
BitStorm 6200
Brand: Paradyne Pages: 4
Paradyne COMSPHERE 3910 Regulatory Information preview
COMSPHERE 3910
Brand: Paradyne Pages: 10
Paradyne COMSPHERE 3800PLUS Installation Instructions Manual preview
COMSPHERE 3800PLUS
Brand: Paradyne Pages: 12
Paradyne Hotwire 8775 Installation Instructions Manual preview
Hotwire 8775
Brand: Paradyne Pages: 26
Paradyne COMSPHERE 3830 Quick Reference preview
COMSPHERE 3830
Brand: Paradyne Pages: 20
Comtech EF Data CDM-600L Installation And Operation Manual preview
CDM-600L
Brand: Comtech EF Data Pages: 206
ELSA MicroLink 14.4TQ User Manual preview
MicroLink 14.4TQ
Brand: ELSA Pages: 114
axing EOC 20-02 Quick Start preview
EOC 20-02
Brand: axing Pages: 4
Patton electronics 1092A User Manual preview
1092A
Brand: Patton electronics Pages: 19
3onedata 277 Series Quick Installation Manual preview
277 Series
Brand: 3onedata Pages: 3
ProSoft Technology RLXIC-SG User Manual preview
RLXIC-SG
Brand: ProSoft Technology Pages: 136
Proscend 5099N Series User Manual preview
5099N Series
Brand: Proscend Pages: 102
Terayon DOCSIS TJ 700 Series Installation Manual preview
DOCSIS TJ 700 Series
Brand: Terayon Pages: 24
Flash TC4300 Quick Installation Manual preview
TC4300
Brand: Flash Pages: 2
Franklin U210 User Manual preview
U210
Brand: Franklin Pages: 22

Brands by name

Popular brands

Load more brands