manualshive.com logo in svg

Paradyne COMSPHERE 6800 Series, Command Reference Manual

The Paradyne COMSPHERE 6800 Series is a cutting-edge telecommunications product designed to revolutionize connectivity. Our comprehensive manual provides step-by-step Installation and Enabling/Disabling Instructions, allowing users to seamlessly set up and configure the device. Download this manual for free from our website to unlock the full potential of your Paradyne COMSPHERE 6800 Series.

Share
Download
background image

2

Modem/DSU Commands

2-147

6800-A2-GB31-20

January 1997

NOTE

If the inventory state of the specified remote modem is limited
access, the Remote dial number field is a required field. If the
inventory state of the specified remote modem is active, the
Remote dial number field is not displayed. If the inventory state of
the specified remote modem is other than limited access or active
(i.e., stock, on order, repair, removed), an error message is
displayed.

Local master device (Required field)

Enter the local 3800/3900 Series modem to be the clone master. The firmware residing in
the specified master modem will be downloaded to the remote device.

NOTE

If the inventory state of the specified remote modem is active, the
Local master device field is displayed as a protected field. The
field is populated with a link level address derived from the link level
address contained in the remote modem’s device profile. (The
address is derived by stripping the last-level network address from
the remote modem’s link level address.) If no device profile exists or
if your network permission is denied to this modem, the derived
address will not be displayed, and you will receive an error
message.

The input form that appears when a 3900 mp single download is specified only contains the
Remote device and Local master device fields, as described previously.

This input form appears when a 3900 mp link download is specified; it contains the following
field:

Link Participation

Enter the type of multipoint link clone to remote download to be performed. Valid entries
are all and partial. Selecting all allows the download to be performed when all of the Poll
List Active link-attached remote modems are participating in the download process.
Selecting partial allows the download even if there are nonparticipating modems in the
Active Poll List. Selecting partial runs the risk of having modems with different
firmware versions in different tributaries being on the same line. A confirm message will
display asking you to continue or cancel.

Since multipoint link firmware download depends on the active poll list, the accuracy of
the active poll list is critical to the success of the download. Another confirm message
will display, asking you to verify the correctness of the active poll list before executing
the download.

Summary of Contents for COMSPHERE 6800 Series














































































































































































































































Reviews:

No comments

Related manuals for COMSPHERE 6800 Series

D-Link DU-562M - 56 Kbps Fax User Manual preview
DU-562M - 56 Kbps Fax
Brand: D-Link Pages: 31
CS RV50 Instruction Manual preview
RV50
Brand: CS Pages: 50
Patton electronics NetLink 1082/I User Manual preview
NetLink 1082/I
Brand: Patton electronics Pages: 28
TC Communications TC2400 User Manual preview
TC2400
Brand: TC Communications Pages: 23
Asus USB-AX56 Quick Start Manual preview
USB-AX56
Brand: Asus Pages: 4
Asus CMAX6000 User Manual preview
CMAX6000
Brand: Asus Pages: 47
Asus DSL-AC68U Quick Start Manual preview
DSL-AC68U
Brand: Asus Pages: 173
Honeywell E-Mon E10039 Installation And Setup Manual preview
E-Mon E10039
Brand: Honeywell Pages: 36
Honeywell CLOUDLINK 4G M1 Quick Start preview
CLOUDLINK 4G M1
Brand: Honeywell Pages: 4
Honeywell Cloud Link 4G Modem User Manual preview
Cloud Link 4G Modem
Brand: Honeywell Pages: 71
Honeywell Fire-Lite 2UD Mounting Instructions preview
Fire-Lite 2UD
Brand: Honeywell Pages: 2
LG M13 Device Description preview
M13
Brand: LG Pages: 21
LG VL600 User Manual preview
VL600
Brand: LG Pages: 40
LG LXU-800 User Manual preview
LXU-800
Brand: LG Pages: 63
LG SmartThinQ LCW-003 Owner'S Manual preview
SmartThinQ LCW-003
Brand: LG Pages: 353
LG ThinQ Wi-Fi MODEM Owner'S Manual preview
ThinQ Wi-Fi MODEM
Brand: LG Pages: 16
LG SmartThinQ LCW-005 Installation Manual preview
SmartThinQ LCW-005
Brand: LG Pages: 11
Nokia USB Modem Manual preview
USB Modem
Brand: Nokia Pages: 10

Brands by name

Popular brands

Load more brands