manualshive.com logo in svg

Paradyne COMSPHERE 3800 Series, User Manual

The Paradyne COMSPHERE 3800 Series offers advanced telecommunications solutions. Stay up-to-date with the latest features and enhancements through our free Firmware Update. Download the comprehensive manual from manualshive.com to maximize your usage and unlock the full potential of this cutting-edge product.

Share
Download
background image

COMSPHERE 3800 Series Modems

9-36

September 1998

3810-A2-GB30-30

Table 9-6

(4 of 6)

V.42/MNP/Buffer Configuration Options

*Flw Cntl of Mdm: Disable

Nxt

Disable

XON/XOFF

RTS_to_Mdm

Flow Control of Modem. Determines how the DTE controls the flow of data from the modem.

Disable – The DTE cannot control the flow of data from the modem.

XON/XOFF – Method of flow control in which the modem starts and stops data flow based upon XON and XOFF
characters received from the DTE.

RTS to Modem – Method of flow control in which the modem respectively starts and stops data transmission based
upon the ON and Off state of the DTE’s RTS signal.

The factory default is Disable.

AT commands for Disable are \Q0, \Q2, and \Q4. 
AT commands for XON/XOFF are \Q1 and \Q5. 
AT commands for CTS to DTE are \Q3 and \Q6.

*XON/XOFF Psthru: Disable

Nxt

Disable

Enable

XON/XOFF Passthrough. Considers an XON/XOFF character as data and passes it on to the remote modem. In this
case, the DTE at one end of the communications link can send flow control characters to the other DTE. This is also
known as DTE to DTE flow control.

Disable – Flow control characters are processed but are not passed on to the remote modem.

Enable – Flow control characters are processed and passed on to the remote modem.

The factory default is Disable.

NOTE:  This configuration option is only available if the Flow Control configuration option is configured for XON/XOFF.

AT command for Disable is \X0. 
AT command for Enable is \X1.

*Mdm/Mdm FlowCtl: Disable

Nxt

Disable

Enable

Modem-to-Modem Flow Control. If a modem’s buffers begin to fill due to data it is receiving from the remote modem, but
is not passing on to the DTE, it can issue XON/XOFF flow control characters to the remote modem. This only applies if
Buffer (nonerror control) mode is selected. If Error Control mode is enabled, flow control between the modems will
happen automatically, regardless of the setting of this option.

Disable – Modem does not respond to XON and XOFF characters received over the VF line. Also, the modem will not
transmit an XOFF character to the remote end if its receive buffers are full.

Enable – Modem stops transmitting data to the remote modem if it receives an XOFF character over the VF line. An
XON character will enable data transmission. Also, the modem will transmit an XOFF character to the remote end if its
receive buffers are full. Select this setting if the DTE rate is less than the VF line rate or if the DTE must frequently stop
the flow of data to process it.

The factory default is Disable.

NOTE:  This configuration option is only available if Flow Control is configured for XON/XOFF.

AT Command for Disable is \G0. 
AT Command for Enable is \G1.

* This configuration option is only available if Async/Sync Mode is configured for Async. Refer to the DTE Interface

configuration options group for more on Async/Sync Mode.

Summary of Contents for COMSPHERE 3800 Series






















































































































































































































Reviews:

No comments

Related manuals for COMSPHERE 3800 Series

iiNet MOBIIBROADBAND 4G Quick Install Manual preview
MOBIIBROADBAND 4G
Brand: iiNet Pages: 2
iiNet ADSL2+ Modem User Manual preview
ADSL2+ Modem
Brand: iiNet Pages: 55
Belkin F5D5530-W User Manual preview
F5D5530-W
Brand: Belkin Pages: 12
Yahoo! BB Trio Modem 26M Setup Manual preview
BB Trio Modem 26M
Brand: Yahoo! Pages: 6
B+B SmartWorx ZXT24-RM Quick Start Manual preview
ZXT24-RM
Brand: B+B SmartWorx Pages: 2
Swarm Tile Product Manual preview
Tile
Brand: Swarm Pages: 63
SMC Networks EZ Connect SMC8002CM Installation Manual preview
EZ Connect SMC8002CM
Brand: SMC Networks Pages: 34
O2 C888 Quick Start Manual preview
C888
Brand: O2 Pages: 8
Franklin Technology Sprint U772 User Manual preview
Sprint U772
Brand: Franklin Technology Pages: 40
Uconnect WA-232E User Manual preview
WA-232E
Brand: Uconnect Pages: 8
IPWireless PCMCIA User Manual preview
PCMCIA
Brand: IPWireless Pages: 40
Motorola M-Series Owner'S Manual preview
M-Series
Brand: Motorola Pages: 24
COBHAM USB Wireless Control Module (UWCM) User Manual preview
USB Wireless Control Module (UWCM)
Brand: COBHAM Pages: 23
D-Link DCM202 - Express Ethernetwork DOCSIS 2.0 Cable... Quick Installation Manual preview
DCM202 - Express Ethernetwork DOCSIS 2.0 Cable...
Brand: D-Link Pages: 7
EchoStar HUGHES HT2000W User Manual preview
HUGHES HT2000W
Brand: EchoStar Pages: 53
Lancom 1781-4G Manual preview
1781-4G
Brand: Lancom Pages: 26
Huawei EchoLife HG612 User Manual preview
EchoLife HG612
Brand: Huawei Pages: 58
Huawei HiLink E3131 Product Description preview
HiLink E3131
Brand: Huawei Pages: 19

Brands by name

Popular brands

Load more brands