Paradyne COMSPHERE 3800 Series User Manual Download

Page: 27 / 213

COMSPHERE 3800 Series Modems

2-8

September 1998

3810-A2-GB30-30

Removing and Replacing
Model 3810 and
Model 3820 Modems

To remove and replace a Model 3810 or Model 3820

modem, perform the following steps:

1. Make sure the modem is offline, and press the

modem’s rear panel power switch to the Off
position.

2. Disconnect the power cord from the ac power

outlet, and then from the connector on the rear of
the modem.

3. Disconnect the dial and leased-line modular cords

from the modem’s rear panel.

4. Disconnect the DTE interface cable from the

modem’s rear panel.

If the modem is to be removed for service, return
it using the procedures on page A in the front of
this document for contact information.

5. Install the replacement modem as described in the

Model 3810 or Model 3820 Modem Installation
section of this chapter, and configure it the same
way as the modem being replaced.

Summary of Contents for COMSPHERE 3800 Series






















































































































































































































Search results

Summary of Contents for COMSPHERE 3800 Series

Reviews:

Related manuals for COMSPHERE 3800 Series

Brands by name

Popular brands

Paradyne COMSPHERE 3800 Series, User Manual

Search results

Summary of Contents for COMSPHERE 3800 Series

Reviews:

Related manuals for COMSPHERE 3800 Series

Brands by name

Popular brands