Paradyne COMSPHERE 3800 Series User Manual Download

Page: 151 / 213

COMSPHERE 3800 Series Modems

14-10

September 1998

3810-A2-GB30-30

Table 14-1

(8 of 12)

3800 Series AT Commands

Command

Front Panel

Branch

Description

&Mn

and &Qn

Async/Sync Mode and DTE Dialer Type

&M0, &Q0

Modem operates in Asynchronous mode and uses
AT Command protocol.

&M1, &Q1

Modem operates in Synchronous mode and uses
AT Command protocol.

&M2, &Q2

Modem operates in Synchronous mode and dials telephone
number stored in directory location 1 when DTR signal turns
Off and then ON.

&M3, &Q3

Modem operates in Synchronous mode and uses
AT Command protocol.

&Q4

Modem operates in Asynchronous mode and uses
AT Command protocol; Hayes AutoSync is enabled.

&M231, &Q231

Modem operates in Asynchronous mode; the DTE
Dialer Type is disabled.

&M232, &Q232

Modem operates in Asynchronous mode; V.25bis Async
dialing is enabled.

&M233, &Q233

Modem operates in Synchronous mode; V.25bis Bisync
dialing is enabled.

&M234, &Q234

Modem operates in Synchronous mode; V.25bis HDLC
dialing is enabled.

&M235, &Q235

Modem operates in Asynchronous mode; AT&T
Exclusive dialing is enabled.

&M236, &Q236

Modem operates in Synchronous mode; the DTE Dialer
Type is disabled.

Configure\Edit\DTE
Dialer

The &M2, &Q2, &M231, &Q231, &M236, and &Q236 commands disable the
use of AT commands and force the modem into Dumb mode. The only way to
gain control of the modem is the front panel.

&Rn

RTS Action

&R0 Standard

RS232.

&R1 Ignores

RTS.

&R2 Simulated Control Carrier.

Configure\Edit\DTE
Interface

&Sn

DSR Control

&S0 Forced On.
&S1 Standard

RS232.

&S2 Wink When Disconnect.
&S3

Follows DTR.

&S4 On

Early.

&S5 Delay to DTE.
&S6

Dial Backup Toggle.

Configure\Edit\DTE
Interface

Summary of Contents for COMSPHERE 3800 Series






















































































































































































































Search results

Summary of Contents for COMSPHERE 3800 Series

Reviews:

Related manuals for COMSPHERE 3800 Series

Brands by name

Popular brands

Paradyne COMSPHERE 3800 Series, User Manual

Search results

Summary of Contents for COMSPHERE 3800 Series

Reviews:

Related manuals for COMSPHERE 3800 Series

Brands by name

Popular brands