manualshive.com logo in svg

Paradyne COMSPHERE 3800 Series, User Manual

The Paradyne COMSPHERE 3800 Series offers advanced telecommunications solutions. Stay up-to-date with the latest features and enhancements through our free Firmware Update. Download the comprehensive manual from manualshive.com to maximize your usage and unlock the full potential of this cutting-edge product.

Share
Download
background image

Configure Branch

9-13

3810-A2-GB30-30

September 1998

Table 9-1

(6 of 7)

DTE Interface Configuration Options

LSD Control: Stndrd_RS232
Nxt    Stndrd_RS232    Forced_On    WinkWhenDisc Follows_DTR    Sim_Cntrl_Car    =DTR/DiscOff    
BridgeRetrain

Line Signal Detect Control. LSD is a signal indicating that the carrier signal is being received from the remote modem. It
is normally turned Off to the DTE when the power level of the received carrier signal drops below the carrier detect
threshold.

Standard RS232 – LSD is ON when the modem detects the remote modem’s carrier signal. LSD turns Off when the
carrier signal strength drops below carrier detect threshold.

Forced On – Forces LSD to be ON at all times.

Wink When Disconnect – LSD is normally forced ON, but can be turned Off for 1 to 2 seconds upon a disconnect. This
is used for UNIX DTEs.

Follows DTR – The state of LSD follows the state of DTR. When DTR turns ON, LSD turns ON. When DTR turns Off,
LSD turns Off.

Simulated Control Carrier – LSD follows the state of RTS of the remote DTE via the V.13 simulated control carrier
signaling. This is required for hosts that cannot support full-duplex operation.

NOTE:  If LSD Control is set for simulated control carrier, then the RTS Action configuration option on the remote

modem must be set for Simulated Control Carrier.

=DTR/Disconnect Off – The state of LSD follows the state of DTR except when disconnecting once a connection is
established. In this instance, DTR remains ON and LSD turns Off. DTR must then toggle Off and then ON again for LSD
to turn ON. This setting is required for AT&T DATAKIT

r

 dial-out applications.

BridgeRetrain – LSD behaves as if it were set for Standard RS232, except that it is turned off when a retrain condition
lasts longer than10 seconds, and turned on again when no retrain condition is detected for a period of 10 seconds.

NOTE:  If LSD Control is set for =DTR/DiscOff, then the DTR Action configuration option must be set for Stndrd_RS232.

For Async Dial, Sync Dial, and Sync Leased, Stndrd_RS232 is the factory default.

For UNIX Dial, WinkWhenDisc is the factory default.

AT command for Forced On is &C0.
AT command for Standard RS232 is &C1. 
AT command for Wink When Disconnect is &C2. 
AT command for Follows DTR is &C3. 
AT command for Simulated Control Carrier is &C4.  
AT command for =DTR/Disconnect Off is &C5. 
AT command for BridgeRetrain is &C6.

TX Clock Source: Internal
Nxt

Internal

External

RXC_Loop

Transmit Clock Source. Determines the source of timing for synchronous data transmitted from the DTE.

Internal – The transmit data’s clock source is derived from the modem’s internal clock and output on Pin 15 (TXC) of the
EIA-232-D interface.

External – The transmit data’s clock source is provided by the DTE on Pin 24 (EXT) on the EIA-232-D interface.

Receive Clock Loop – The modem’s transmit clock is derived from its received signal and is output on Pin 15 (TXC) of
the EIA-232-D interface.

NOTE:  This configuration option only appears if Async/Sync Mode is configured for Sync.

The factory default is Internal.

AT command for Internal is &X0. 
AT command for External is &X1. 
AT command for RXC Loop is &X2.

Summary of Contents for COMSPHERE 3800 Series






















































































































































































































Reviews:

No comments

Related manuals for COMSPHERE 3800 Series

NEC Speed Wi-Fi NEXT WX01 Instruction Manual preview
Speed Wi-Fi NEXT WX01
Brand: NEC Pages: 2
Campbell RF401 Quick Start Manual preview
RF401
Brand: Campbell Pages: 4
Sprint Ride-Fi User Manual preview
Ride-Fi
Brand: Sprint Pages: 78
SG Wireless SGW8100 User Manual preview
SGW8100
Brand: SG Wireless Pages: 6
Multi-Tech MultiModem MT5634ZBA-V.92 Quick Start Manual preview
MultiModem MT5634ZBA-V.92
Brand: Multi-Tech Pages: 16
Cyta ZXDSL 931VII Installation Manual preview
ZXDSL 931VII
Brand: Cyta Pages: 20
ASL Holdings Limited ASLH306 User Manual preview
ASLH306
Brand: ASL Holdings Limited Pages: 29
Paradyne COMSPHERE 392xPlus Installation And Operation Manual preview
COMSPHERE 392xPlus
Brand: Paradyne Pages: 285
Cal Amp 819-1XRT SERIES User Manual preview
819-1XRT SERIES
Brand: Cal Amp Pages: 48
USR IOT USR-G806 User Manual preview
USR-G806
Brand: USR IOT Pages: 47
NETGEAR CM212 Installation Manual preview
CM212
Brand: NETGEAR Pages: 19
NETGEAR CG2003D User Manual preview
CG2003D
Brand: NETGEAR Pages: 61
NETGEAR CM600 User Manual preview
CM600
Brand: NETGEAR Pages: 26
Vololink VoloFone VF100 User Manual preview
VoloFone VF100
Brand: Vololink Pages: 50
TC Communications TC2100 User Manual preview
TC2100
Brand: TC Communications Pages: 26
Patton electronics 1012B User Manual preview
1012B
Brand: Patton electronics Pages: 16
Patton electronics RocketLink-G 3088 Series User Manual preview
RocketLink-G 3088 Series
Brand: Patton electronics Pages: 48
Huawei EchoLife HG612 User Manual preview
EchoLife HG612
Brand: Huawei Pages: 58

Brands by name

Popular brands

Load more brands