manualshive.com logo in svg

Paradyne COMSPHERE 3800 Series, User Manual

The Paradyne COMSPHERE 3800 Series offers advanced telecommunications solutions. Stay up-to-date with the latest features and enhancements through our free Firmware Update. Download the comprehensive manual from manualshive.com to maximize your usage and unlock the full potential of this cutting-edge product.

Share
Download
background image

3-1

3810-A2-GB30-30

September 1998

Model 3811 Installation

Overview

3-1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Model 3811 Installation

3-2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Removing and Replacing Model 3811 Modems

3-4

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Overview 

The carrier-mounted Model 3811 modem (Figure 3-1)

is capable of dial or 4-wire/2-wire leased-line operation
and installs into a COMSPHERE 3000 Series Carrier. The
Model 3811’s faceplate has 16 LED status indicators for
displaying modem activity and an audio speaker jack for
the carrier’s optional speaker.

The Model 3811 modem’s rear has two DTE edge card

connectors that mount into a connector plate located on
the rear of the carrier. This connector plate has two
DB-25-S connectors, one providing an EIA RS-232 DTE
interface and one providing an EIA RS-366A DTE
interface. The Model 3811 derives ac power from the
COMSPHERE 3000 Series Carrier’s backplane which is a
common bus to all devices installed in the carrier. The
user interface to any Model 3811 is through the shared
diagnostic control panel (SDCP), an optional feature

similar to the DCPs on the Model 3810 and Model 3820.
For a better understanding of DCP operation, refer to
Chapter 4, DCP Operation.

The COMSPHERE 3000 Series Carrier has a total of

17 slots. The first slot, Slot 0, is reserved for the Shared
Diagnostic Unit (SDU) while the remaining 16 slots can
house up to 16 Model 3811 modems, or for mixed
networks, a combination of Model 3811 modems and
Model 3611 Data Service Units (DSUs). An SDU is a
circuit card that provides SDCP and network management
interfaces to modems and DSUs installed in the carrier.
SDUs are only required if a single SDCP is used by
multiple COMSPHERE 3000 Series Carriers in a cabinet
or if a network management system (NMS) is used.

For more details on the COMSPHERE 3000 Series

Carrier, refer to the COMSPHERE 3000 Series Carrier,
Installation Manual.

3

Summary of Contents for COMSPHERE 3800 Series






















































































































































































































Reviews:

No comments

Related manuals for COMSPHERE 3800 Series

US Robotics USR265633B Specifications preview
USR265633B
Brand: US Robotics Pages: 2
B&B Electronics Zlinx Xtreme ZXT24-RM User Manual preview
Zlinx Xtreme ZXT24-RM
Brand: B&B Electronics Pages: 163
Huawei E8231 Product Description preview
E8231
Brand: Huawei Pages: 24
Zte MF626 User Manual preview
MF626
Brand: Zte Pages: 30
Cermetek CH1794 Manual preview
CH1794
Brand: Cermetek Pages: 19
Lantronix M110 Series Command Reference Manual preview
M110 Series
Brand: Lantronix Pages: 56
Four-Faith F2 46-D Series User Manual preview
F2 46-D Series
Brand: Four-Faith Pages: 35
Ebyte NA111 User Manual preview
NA111
Brand: Ebyte Pages: 31
nawras E5 II Manual preview
E5 II
Brand: nawras Pages: 29
SMC Networks EZ Connect SMC8002CM-US Specification preview
EZ Connect SMC8002CM-US
Brand: SMC Networks Pages: 2
SMC Networks EZ Connect SMC8004CM Specifications preview
EZ Connect SMC8004CM
Brand: SMC Networks Pages: 2
CommScope SURFboard SBG8300 User Manual preview
SURFboard SBG8300
Brand: CommScope Pages: 68
US Robotics 2884C Quick Installation Manual preview
2884C
Brand: US Robotics Pages: 80
Tainet DT-128 Series User Manual preview
DT-128 Series
Brand: Tainet Pages: 33
RadioLabs O2Connect Installation Manual preview
O2Connect
Brand: RadioLabs Pages: 8
Satel SATELLINE-EASy Pro 35W User Manual preview
SATELLINE-EASy Pro 35W
Brand: Satel Pages: 104
Satel SATELLINE-2ASxE User Manual preview
SATELLINE-2ASxE
Brand: Satel Pages: 48
Abocom UTA128 Quick Installation Manual preview
UTA128
Brand: Abocom Pages: 19

Brands by name

Popular brands

Load more brands