manualshive.com logo in svg

Paradyne COMSPHERE 3800 Series, User Manual

The Paradyne COMSPHERE 3800 Series offers advanced telecommunications solutions. Stay up-to-date with the latest features and enhancements through our free Firmware Update. Download the comprehensive manual from manualshive.com to maximize your usage and unlock the full potential of this cutting-edge product.

Share
Download
background image

COMSPHERE 3800 Series Modems

4-8

September 1998

3810-A2-GB30-30

Top-Level Menu Status and 
Operational Messages

Access to all menu tree branches from the DCP begins

at the Top-Level menu, the head of the menu hierarchy.

The LCD’s top line identifies the modem status, as listed
in Table 4-4, while the bottom line displays the main
menu tree branches and operational and dial access
security messages, as listed in Table 4-5 and Table 4-6.

Table 4-4

(1 of 3)

Top-Level Menu Status

Normal Operation

Status Message

Indicates

Fax Rx:MR*

Indicates that the modem is online, in fax receive modem, operating at the displayed data rate.

Fax Tx:MR*

Indicates that the modem is online, in fax transmit mode, operating at the displayed data rate.

Idle:MR*

The modem is configured for dial network operation and is on-hook.

Leased:MR*

The modem is operating on leased lines at the displayed data rate.

OnLine:MR* EC**

Indicates the modem is online, in Data mode, and operating at the displayed data rate. EC (error
control) displays if error control is operational.

Ring Indicate

The local modem is receiving an incoming ring.

Test:MR*

The modem is in test mode operating at the displayed data rate.

Alarm Status

Message***

Indicates

Make Busy

Indicates the modem is in a Make Busy condition.

Power On Fail

Indicates the modem has failed its Power-On Self-Test.

Self Health Fail

Indicates a failure in the modem’s hardware components.

Weak Battery

Indicates the battery is operating below 2 volts. Contact your sales or service representative.

Normal Call

Setup Messages

Indicates

Off Hook

The modem is off-hook and waiting to dial a telephone number.

Dialing

The remote modem is ringing.

Training

The modem is training or retraining.

EC Negotiating

The local and remote modems are negotiating the highest possible level of error control
compatible between both modems. Once a level is selected, this LCD message disappears.

* MR. Modem Rate indicates the data rate the modem is using. One of the following values appears: 300, 1200, 2400, 

4800, 7200, 9600, 12K (12,000), 14.4 (14,400), 16.8 (16,800), or 19.2 (19,200) bps.

** EC. Error Control indicates the modem is online and using V.42 or MNP error control. One of the following values 

appears after the modem rates listed above: MNP2, MNP3, MNP4, MNP5, V42, V42b, or NoEC. (NoEC indicates the 
modem is connected in Buffer mode rather than error control. If an EC value does not appear, then the modem is in 
Direct mode.)

*** The Alarm Status Messages only appear when the Normal Operation Status Messages display; the LCD alternates 

between the two message sets.

Summary of Contents for COMSPHERE 3800 Series






















































































































































































































Reviews:

No comments

Related manuals for COMSPHERE 3800 Series

Patton electronics 1025 User Manual preview
1025
Brand: Patton electronics Pages: 9
RAK WisGate Edge Lite 2 RAK7268V2 Quick Start Manual preview
WisGate Edge Lite 2 RAK7268V2
Brand: RAK Pages: 9
Optelecom 9525AY Installation And Operation Manual preview
9525AY
Brand: Optelecom Pages: 26
Abocom USB ADSL Modem UAM700 Quick Installation Manual preview
USB ADSL Modem UAM700
Brand: Abocom Pages: 15
Aztech 56K PCI Modem Manual preview
56K PCI Modem
Brand: Aztech Pages: 16
Ubee DDW3612 User Manual preview
DDW3612
Brand: Ubee Pages: 70
Digi E230 User Manual preview
E230
Brand: Digi Pages: 19
tell S900 B09 Applications Manual preview
S900 B09
Brand: tell Pages: 11
Zte K2525 Quick Start Manual preview
K2525
Brand: Zte Pages: 16
NimbeLink Skywire LTE CAT1 User Manual preview
Skywire LTE CAT1
Brand: NimbeLink Pages: 25
US Robotics 005689-03 Manual preview
005689-03
Brand: US Robotics Pages: 68
3Com 3COMIMPACT IQ User Manual preview
3COMIMPACT IQ
Brand: 3Com Pages: 160
CommScope ARRIS SURFboard SB8200 User Manual preview
ARRIS SURFboard SB8200
Brand: CommScope Pages: 32
Zte K4203-Z Quick Manual preview
K4203-Z
Brand: Zte Pages: 9
HORNER CGM750 Product Specifications And Installation Data preview
CGM750
Brand: HORNER Pages: 8
Tosibox Oy TB4GM2EU User Manual preview
TB4GM2EU
Brand: Tosibox Oy Pages: 4
Rae RAELink3 Quick Reference preview
RAELink3
Brand: Rae Pages: 5
Lanpro LP-510G Installation Manual preview
LP-510G
Brand: Lanpro Pages: 3

Brands by name

Popular brands

Load more brands