manualshive.com logo in svg

Paradyne COMSPHERE 3800 Series, User Manual

The Paradyne COMSPHERE 3800 Series offers advanced telecommunications solutions. Stay up-to-date with the latest features and enhancements through our free Firmware Update. Download the comprehensive manual from manualshive.com to maximize your usage and unlock the full potential of this cutting-edge product.

Share
Download
background image

Configure Branch

9-17

3810-A2-GB30-30

September 1998

Table 9-2

(3 of 5)

DTE Dialer Configuration Options

*Backspace Char: 008 ASCI

Nxt

↑

008

ASCI

Backspace Character. Sets the character used to perform a backspace in Command mode.

The factory default is 08 (ASCII backspace character).

AT command is S-register S5 = n, where n is a value from 0 to 127.

*Linefeed Char: 010 ASCI

Nxt

↑

010

ASCI

Line Feed Character. Sets the character used to perform a line feed in Command mode for responses from the modem.

The factory default is 10 (ASCII line feed character).

AT command for Line Feed Character is S-register S4 = n, where n is a value from 0 to 127.

*Result Codes: Enable

Nxt

Enable

Disable

EnableInOrig

Result Codes. Result codes are informational messages (such as Connect and Ring) sent from the modem and
displayed on the asynchronous DTE terminal. (For a list of result codes, refer to Table B-1 in Appendix B.)

Enable  – Modem sends result codes to the DTE.

Disable – Modem does not send result codes to the DTE.

EnableInOrig – For UNIX applications, enable result codes only on the originating modem. This prevents the DTE on
the answer side from interpreting result codes as login attempts.

For Async Dial, Enable is the factory default. 
For UNIX Dial, EnableInOrig is the factory default.

AT command to enable is Q0. 
AT command to disable is Q1. 
AT command to enable in Originate mode is Q2.

*ExtendResltCode: Enable

Nxt Enable

Disable

Add/EC

Add/V42,MNP

Use_DTE_Rate

Extended Result Codes. Informational messages such as VF data rate and Error Control are displayed with the result
codes. (For a list of Extended Result Codes, refer to Table B-1 in Appendix B.)

Enable  – Result codes include NO DIALTONE, BUSY, NO ANSWER, and CONNECT xxxx (where xxxx is the VF data
rate).

Disable – Only OK, CONNECT, RING, NO CARRIER, and ERROR result codes appear.

NOTE:  NO DIALTONE is valid only if Dial Tone Detect configuration option is enabled. BUSY appears if Busy Detect

configuration option is enabled.

Add/EC – Places the EC suffix after the result code text if error control is used. For example, CONNECT 9600/EC

Add/V.42,MNP – Places either the /V.42 or /MNP suffix after the result code text if data compression is used. For
example, CONNECT 9600/V42b.

Use DTE Rate – Allows the DTE rate to be displayed in the Connect message instead of the line rate. This feature is
required in some modem pooling applications.

The factory default is Enable.

AT command to disable is X0.
AT commands to enable are X1, X2, X3, or X4. 
AT command for Add/EC is X5. 
AT command for Add/V42, MNP is X6. 
AT command for Use DTE Rate is X7.

* This configuration option only appears if DTE Dialer Type is configured for AT.

Summary of Contents for COMSPHERE 3800 Series






















































































































































































































Reviews:

No comments

Related manuals for COMSPHERE 3800 Series

Dare DB101 User Manual preview
DB101
Brand: Dare Pages: 26
Arris TM02AA104 Installation Manual preview
TM02AA104
Brand: Arris Pages: 52
TP-Link Archer T6E Quick Installation Manual preview
Archer T6E
Brand: TP-Link Pages: 1
TP-Link Archer VR300 User Manual preview
Archer VR300
Brand: TP-Link Pages: 98
Multitech MT5634ZLXI/E Product Update preview
MT5634ZLXI/E
Brand: Multitech Pages: 4
Home Screen HomeScreen Quick Start Manual preview
HomeScreen
Brand: Home Screen Pages: 4
ESTeem 210C User Manual preview
210C
Brand: ESTeem Pages: 78
ActionTec GT724WGR Specifications preview
GT724WGR
Brand: ActionTec Pages: 4
ActionTec External 56K Call Waiting User Manual preview
External 56K Call Waiting
Brand: ActionTec Pages: 33
ActionTec GT701A User Manual preview
GT701A
Brand: ActionTec Pages: 119
Belkin F5D5530-W User Manual preview
F5D5530-W
Brand: Belkin Pages: 12
Paradyne COMSPHERE 3921PLUS Installation Instructions preview
COMSPHERE 3921PLUS
Brand: Paradyne Pages: 2
RadioLinx RLX-FHS Quick Start Manual preview
RLX-FHS
Brand: RadioLinx Pages: 16
3Com U.S. Robotics 56K Professional Message User'S Manual And Reference preview
U.S. Robotics 56K Professional Message
Brand: 3Com Pages: 37
BT Huawei E180 User Manual preview
Huawei E180
Brand: BT Pages: 24
Coster GSM 822 Manual preview
GSM 822
Brand: Coster Pages: 4
Lucent Technologies 4703US Reference Manual preview
4703US
Brand: Lucent Technologies Pages: 80
Raymar V.32M/14.4 Specification Sheet preview
V.32M/14.4
Brand: Raymar Pages: 2

Brands by name

Popular brands

Load more brands